For best results, we suggest that you tighten the four Allen bolts in sides of main easel frame, as shown in Figure 1, and tighten the two Phillips screws in the back of canvas support assembly, as shown in Figure 2. 2 Lay main easel frame flat on floor with brass height adjustment track facing up. □ Carefully slide canvas support assembly from below into slots and tracks in main frame, as shown in Figure 3. Pull spring-loaded height-adjustment ring and set in the third track position for th

Always use direct replacement lamps in order to prevent overheating. 2. Disconnect the power cord. 3. Remove the screws and aluminum strips from the top surface of the lightbox. Carefully remove glass and Plexiglas panels. Degrees of Illumination MODEL No. Lumens Tubes Lumens at per Tube per Box Light Box Surface LB1218 650 1 F15T8 650 LB1620 650 2 F15T8 1300 LB1824 650 2 F15T8 1300 LB2436 1750 3 F30T8 5100 All electrical components are U.L. listed. 4. Remove the hold-down scr

Lumens Tubes Lumens at per Tube per Box Light Box Surface LB1218 650 1 F15T8 650 LB1620 650 2 F15T8 1300 LB1824 650 2 F15T8 1300 LB2436 1750 3 F30T8 5100 All electrical components are U.L. listed. 4. Remove the hold-down screws and lift off the light diffusers. 5. Remove and replace fluorescent tubes. 6. Return diffusers, glass and Plexiglas panels to their original positions. Re-install aluminum strips and screws. T y Alvin & Company, Inc. Bloomfield, CT Grand Prairie, TX www.a

For your own safety, use gloves when handling glass. Place the glass on top of the Plexiglas sheet and replace the aluminum strips. 2. To operate, depress the on/off switch and hold for one or two seconds until the lights illuminate. Note: Bulbs may loosen during shipping. If bulbs don't illuminate check that they are properly seated in fixture. 3. The Satin-Glow Lightbox is designed to operate on 110V AC, 60 cycle. Please do not use any other power source. 4. Removal of the back panel or tam

For your own safety, use gloves when handling glass. Place the glass on top of the Plexiglas sheet and replace the aluminum strips. 2. To operate, depress the on/off switch and hold for one or two seconds until the lights illuminate. Note: Bulbs may loosen during shipping. If bulbs don't illuminate check that they are properly seated in fixture. 3. The Satin-Glow Lightbox is designed to operate on 110V AC, 60 cycle. Please do not use any other power source. 4. Removal of the back panel or tam

WTF35 B C E CONTENTS Key Qty. Description A 1 Grid Tray with small openings B 1 Frame Section with rubber feet C 2 Grid Tray with large openings D 1 Frame Section E 2 Covered Casters with lock nuts F 2 Side Braces (left and right) G 1 Dust Protector bottom cover (Optional) 12 Nuts, 4 Screws 1. Attach grid tray with small openings(A), to bottom of large frame section(B). 2. Attach remaining two trays(C). 3. Secure smaller frame section(D) in the same manner. 4. Using encl

WSF36 CONTENTS Key Qty. Description A 2 Large Side Grids Back Grid B 1 C 2 Center Grids D 1 Front Grid E 1 Bottom Step F 4 Casters G 1 Bag Small Clips H 1 Bag Large Clips F NOTE: Plastic clips can be snapped on and removed easily by hand. Most grid sections require only 2 clips per side for support. For safety, clips attached on exterior of cart should be positioned with flanges facing inward. (See reverse side for assembly) CLIP ATTACHMENT TAIWAN Assembly Instructions for No

Align holes in front leg extensions (D) with holes in table top as shown in Figure 1. Fasten all 1/2" screws (H) and tighten securely. Use care not to overtighten and strip. Carefully return table assembly to the upright position. Adjust table top to desired height using height adjustment knobs (F). You’re finished and your table is ready to use as shown in Figure 2. Folding Table: Drop all extension tubes down to their lowest positions. Lift top up until the front extension tubes (D) diseng

XII-4-XB Tools Required: Phillips screwdriver, drill with VW bit. Parts Included: A 1pc Leg Frame B 1pc Tabletop C 2pcs Rear Extension Tubes (Shipped in separarate box) : D 2pcs Front Extension Tubes F 2pcs Height Adjustment Knobs To Assemble: Unpack all parts and inspect to confirm that all are present. Unfold base (A). Insert rear extension tubes (C) completely into frame (A) and loosely hand-tighten knobs (F). Insert front extension tubes (D) into frame (A). Place table top (B)

Use care to differentiate the four crossbars from each other, as shown in the parts list. Also use care to differentiate left side frame from right, as shown in the parts list. Attach rear crossbars (B and C), footrest crossbar (E), and front crossbar (D) to one side frame (A) using 2" Allen bolts (G) to one) to one ). Pay close attention to correct orientation of all pre- drilled holes. Tighten securely. Attach other side frame to opposite ends of four crossbars in step two using 2" Allen bolts