Assessments - 3, GPA: 4 ( )

Fabricante : Graco Inc. Arquivo Tamanho: 250.11 kb Arquivo Nome : Língua de Ensino:

tube (not 1 4* 156454 O-RING, 010 buna-n 2 shown) 5* 551181 BEARING, air cylinder 2 36 115982 GUN, grease (not shown) 1 6* 154662 O-RING, 222 buna-n 2 37 551187 COUPLER, flush grease 1 7* 552164 DOWEL PIN 1 (not shown) 9* 10 11 12 13 14 15 16*† 18 19 20*† 21* 157628 626703 626704 196018 552163 102817 552161 104371 103610 551188 626705 551191 626064 O-RING, 006 buna-n PISTON, air cylinder CAP, air cylinder CAP, air cylinder; Models 965766 and 965786 only CAP, air cylinder; Models 243482 and 243666 only CLIP, internal 1.75 SCREW, drive PLATE, identification SCREW, 10–32 x 0.375 O-RING, 014 fluoroelastomer FLUSH GREASE FITTING LUBE HOUSING U-CUP, urethane/EPR BEARING, lube 1 1 1 1 2 2 1 4 1 2 1 1 1 38*† 39*† 40 41* 42. 43 44 45 171860 104319 626732 626707 195957 626060 626708 626709 100166 102920 GASKET, seat O-RING, 014 PTFE NOSEPIECE, stainless steel; Models 965766 and 243666 only NOSEPIECE; aluminum; Model 965786 only NOSEPIECE; stainless steel; Model 243482 only RING, snuff-back SHAFT, adjustment Models 965766 and 965786 only NUT, adjustment Models 965766 and 965786 only NUT, full hex, 10–32 Models 965766 and 965786 only NUT, jam, 10–32 Models 243482 and 2436666 only 1 1 1 1 1 1 1 1 1 1 22*† 551190 U-CUP, Polymite/EPR 1 23. 103926 SCREW, 1/4–20 x 2.25 2 25* 185467 SEAT, C2 carbide 1 * Included in Rebuild Kit 570268. 26 626731 HOUSING, fluid; stainless steel; Model 965766 and 1 † Included in Section Seal Kit 570267. 626706 243282 only HOUSING, fluid; aluminum; Model 965786 only 1 . Replacement Instruction and Warning Labels are available at not cost. 27*. 626062 NEEDLE, hardened stainless steel 1 . Use Loctite Primer N7649 and Loctite TL242, 243, 28. 188377 LABEL, skin injection haz1 or equivalent (“blue” Loctite) when assembling this ard part. 29. 188378 LABEL, read instruction 1 manual . Use anti–seize lubricant (Loctite 56765 or equivalent) when assembling 965766 and 965786. Use Loctite TL242, 243, or equivalent (“blue” Loctite) when assembling 243482 and 243666. 308876 17 18 308876 Parts 8372A 8370A 63 46 48 49 51 52 58 59 57 50 (965768 only) (965767 only) 47 8375B 61 60 53 54 55 56 Service (Models 243482 and 243666 only) WARNING SKIN INJECTION HAZARD To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 8. Disassembly 1. Relieve all air and fluid pressure. 2. Disconnect the valve from the system. 3. Remove the four nosepiece screws (15), and pull the nosepiece (40) away from the valve. Remove the snuff-back ring (41). See Fig. 5, page 14. 4. Use an 1/8 in. pin punch in the needle hole (A) to unscrew the needle (27). If the shaft (3) spins, insert a dowel pin in the shaft hole (B) to hold it steady, then unscrew the needle (27). 5. Remove the seat (25), gasket (38), and o-ring (39). 6. Remove the two fluid housing screws (23) and remove the fluid housing (26). Remove the primary fluid seal (22) from the fluid housing (26). 7. Pull the bearing/lube housing (19) from the air cylinder (1). Remove the bearing (21), bearing o-ring (16), and secondary fluid seal (20). Remove the grease fittings (18). 8. Remove the C-clip (12) from the back of the air cylinder (1). Push the shaft (3) into the air cylinder to dislodge the air cylinder cap (11). Remove the cap o-ring. 9. Remove the internal C-clip (12). Push the shaft (3) to dislodge the piston (10) assembly from the air cylinder (1). 10. Remove the pin (7), o-ring (9), and piston o-ring (6). 11. Use a 1/4 in. pin punch to knock out the bearings (5) and o-rings (4). 308876 19 Service (Models 243482 and 243666 only) Reassembly Air Cylinder Section 1. Lubricate the shaft o-rings (4) and the bearings (5) with grease supplied in the repair kit. Insert o-rings into the air cylinder (1) and air cap (11) cavities. See Fig. 5. 2. Press the bearings (5) flush into the air cylinder housing and air cap, trapping the o-rings (4). 3. Lubricate and reassemble the piston assembly; piston (10), o-ring (9), dowel pin (7), o-ring (6), and shaft (3). Tighten the jam nut (45) to 15–20 in-lb (1.7–2.2 Nm). The shaft (3) should hang with some play to be self-aligning in the bearing. 4. Lubricate the air cylinder (1) ID with the grease supplied. Push the piston (10) assembly into the air cylinder. 5. Orient the air inlet manifold (2) (if used) as shown. Match the gasket openings to the air ports. Fluid Section 1. Lubricate the bearing (21), o-ring (16) and cup seal (20). Put the o-ring (16) on the bearing. Carefully insert the seal (20) into the bearing recess, with the lips of the o-ring facing into the bearing. Be careful not to damage the seal lips. 2. Push the bearing (21) seal end first into the housing (19). Be sure that the grease hole in the side of the bearing lines up with the grease ports in the housing (19). 3. Holding the bearing (21) in place, push the bearing assembly over the shaft (3). 4. Lubricate the main fluid seal (22) and its cavity in the housing (26). Carefully press the seal, li...

Baixe o seu

Para fazer o download, introduza 2 dígitos :