The "cost" to maintain sharp and undamaged accessories is more than offset by the "time saved" in operating the tool with sharp accessories. REMOVING SDS-plus® ACCESSORIES !WARNING Accessories may be hot after use. Avoid contact with skin and use proper protective gloves or cloth to remove. To remove an accessory, pull locking sleeve backward and pull bit forward. All accessories should be wiped clean after removing (Fig. 3). FIG. 2 FIG. 3 DUST SHIELD LOCKING SLEEVE SDS-plus® CHUCK Disconnect ba

When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury. Certain cleaning agents such as gasoline, carbon tetrachloride, ammonia, etc. may damage plastic parts. Safety Rules for Rotary Tools Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories runnin

By referring to these tables, you can discover the recommended speeds for each type of accessory. Look these tables over and become familiar with them. Ultimately, the best way to determine the correct speed for work on any material is to practice for a few minutes on a piece of scrap, even after referring to the chart. You can quickly learn that a slower or faster speed is more effective just by observing what happens as you make a pass or two at different speeds. When working with plastic, for

Do not stare into the beam. Class 2 Laser product. Radiacion laser. No mire al rayo. Producto laser de Clase 2. Rayonnement laser. Ne regardez pas directement dans le faisceau. Produit laser de Classe 2. IEC 60825-1:2007-03 <1mW, 635 nm Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice 50, 7/26/2001 2 OPENOPENOPEN 1 1 2 3 4 5 6 7 9 10 11 8 13 2 605 438 682 12 1 618 C01 066 D CBAOR FEFE -3 14142 607 990 0310 601 015 B10160 601 069 110GH0 601 015 A10171518 6cm

protection. Dust mask, non-skid safety Do not abuse the cord. Never use the shoes, hard hat, or hearing protection must cord to carry the tools or pull the plug be used for appropriate conditions. -2 BM 1619929519 12/02 12/10/02 2:52 PM Page 3 Tool Use and Care other condition that may affect the tools Use clamps or other practical way to operation. If damaged, have the tool secure and support the workpiece to a serviced before using. Many accidents are stable platform. Holding the work by hand

SAVE THESE INSTRUCTIONS Work Area from an outlet. Keep cord away from Keep your work area clean and well lit. heat, oil, sharp edges or moving parts. Cluttered benches and dark areas invite Replace damaged cords immediately. accidents. Damaged cords increase the risk of electric shock. Do not operate power tools in explosive atmospheres, such as in the presence of When operating a power tool outside, useflammable liquids, gases, or dust. Power an outdoor extension cord marked "W-A" tools create

If you TRIGGER SWITCH experience bit binding and clutch begins toYour tool is equipped with a variable speedslip, immediately turn the tool "OFF" andtrigger switch. The tool speed can becorrect the condition leading to the bit binding. controlled from the minimum to the maximum AUXILIARY HANDLE nameplate RPM by the pressure you apply to The auxiliary handle will provide additional the trigger. Apply more pressure to increase control, support and guidance for the tool. The the speed and release p

The term “power tool” inall of the warnings listed below refers to your mains-operated (corded) power tool or battery- operated (cordless) power tool. SAVE THESE INSTRUCTIONS Work area safetyKeep work area clean and well lit. Cluttered or dark areas invite accidents. Do not operate power tools in explosiveatmospheres, such as in the presence offlammable liquids, gases or dust. Power tools create sparks which may ignite the dustor fumes. Keep children and bystanders away whileoperating a power to

The term “tool” in all of the warnings listed below refers to your mains-operated (corded) tool or battery-operated (cordless) tool. !WARNING The following labels are on your laser tool for your convenience and safety. They indicate where the laser light is emitted by the tool. ALWAYS BE AWARE of their location when using the tool. Do not direct the laser beam at persons or animals and do not stare into the laser beam yourself. This tool produces laser class 2 laser radiation and complies with 2

Never use the cord secure and support the workpiece to a to carry the tools or pull the plug from an stable platform. Holding the work by hand or outlet. Keep cord away from heat, oil, sharp against your body is unstable and may lead to edges or moving parts. Replace damaged loss of control. cords immediately. Damaged cords increase the risk of electric shock. -2 BM 1619929567 10-03 3/2/04 9:40 AM Page 3 Do not force tool. Use the correct tool for operation. If damaged, have the tool your applic