Install all protective equipment coversand safety ground leads after setup. Failure to replace covers and groundleads could result in serious injury or death. Models 218, 225, and 132 (Analog) Electronics refer to paragraph 3-2. Model 218A Electronics refer to paragraph 3-3. MODEL TC200 Electronics refer to paragraph 3-4. Model 132 Digital Electronicsrefer to paragraph 3-5. 3-2 MODELS 218, 225, AND 132 (ANALOG) ELECTRONICS SETUP Before beginning operation, it is important that the probe heater s

Page 3-3 Revised Figure 3-1. Updated the paragraph Initial Power Up. Page A-2 thru A-23 Added note 11 to the safety data section. Added additional pages/languages. Page C-1 Updated the return of materials address. Back cover Updated the address blocks. Instruction Manual IM-106-880, Rev 1.0 January 2007 OCX 8800 SECTION 1 Description and Specifications SECTION 2 Installation SECTION 3 Configuration and Startup SECTION 4 Using the LOI SECTION 5 Using HART Communications SECTION 6 Calibration Tabl

N96 Rosemount Analytical Inc. A Division of Emerson Process Management Preface P-5 Instruction Manual 748374-F March 2003 Model NGA2000 TO2 GLOSSARY OF TERMS Analyzer Module The module that contains all sensor/detector components for development of a Primary Variable signal; includes all signal conditioning and temperature control circuitry. Backplane The interconnect circuit board which the Controller Board, Power Supply, Analyzer Module power and network cables, I/O Modules and Expansion Modul

Because these instruments are sophisticated technical products, you MUST properly install, use, and maintain them to ensure they continue to operate within their normal specifications. The following instructions MUST be adhered to and integrated into your safety program when installing, using, and maintaining Rosemount Analytical products. Failure to follow the proper instructions may cause any one of the following situations to occur: Loss of life; personal injury; property damage; damage to th

Based on its review, IARC classified crystalline silica as a group 2A carcinogen (probable human carcinogen). The OSHA permissible exposure limit (PEL for cristobalite is 0.05 mg/m3 (respirable dust). The ACGIH threshold limit value (TLV) for cristobalite is 0.05 mg/m3 (respirable dust) (ACGIH 1991-92). Use NIOSH or MSHA approved equipment when airborne exposure limits may be exceeded. The minimum respiratory protection recommended for given airborne fiber or cristobalite concentrations are: CON

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii Component Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

key. Select the tag of the desired reference channel with the ^ or v keys and then press the . or > key. The display will re turn to the previous menu automatically and the selected reference channel will be displayed in the “Source module:” line. Choose signal Select the “Signals” submenu by selecting the “Choose signal…” line and pressing the . key. Note: the parameters “Operation status” and “Validity” are not functional on the TO2. The list of signals will depend on the module chosen. TO2 37

d. Calibration of Automatic Pressure Compensation Oxygen readout is automatically corrected to within ±1% of fullscale for barometric pressure variations within ±3% of the target value and is corrected to within ±2% of fullscale for variations within ±5% of the target value. The target value may be set anywhere within the range of -2.7 to 3.3 psig ±3 psig ( 18.6 to 22.8 kPa ±21 kPa). The factory setting is 0 psig (0 kPa). This setting is suitable for applications where (a) the analyzer exhaust p

The following instructions MUST be adhered to and integrated into your safety program when installing, using, and maintaining Rosemount Analytical products. Failure to follow the proper instructions may cause any one of the following situations to occur: Loss of life; personal injury; property damage; damage to this instrument; and warranty invalidation. • Read all instructions prior to installing, operating, and servicing the product. • If you do not understand any of the instructions, contact

1.5 Model 3081FG September 2002 d. Installing Model 3081 Transmitter surface using the threaded mounting holes located on the bottom of (2) 2 1. Ensure all components are available to the transmitter housing. Refer to install the Model 3081 Transmitter. Figure 2-6 for installation references. 2. Choose a method or location to mount the transmitter. (b) Pipe Mounting. An optional pipe mounting bracket is available for (a) Flat Surface Mounting. The trans- this type of installation. Refer to mitte