Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
When carrying the projector, use the accessory carrying bag. When placing the projector inside the carrying bag, position it so that the lens is facing upward. Cautions regarding setting-up Observe the following at all times when setting up the projector. Avoid setting up in places which are subject to vibration or shocks. If the projector is set up in locations with strong vibration, such as near a motor, or if it is installed inside a vehicle or on board a ship, the projector may be subjected to vibration or shocks which can damage the internal parts and cause malfunctions or accidents. Accordingly, set up the projector in a place which is free from such vibrations and shocks. Do not set up the projector near high-voltage power lines or near motors. The projector may be subject to electromagnetic interference if it is set up near high-voltage power lines or motors. If installing the projector to the ceiling, ask a qualified technician to carry out all installation work. If the projector is to be suspended from the ceiling, you will need to purchase the separate installation kit (Model No.: ET-PKC75). Furthermore, all installation work should only be carried out by a qualified technician. If using of this projector at high elevations (above 1400 m), consult your dealer or Authorised Service Center. Special measures will be necessary to use this projector at high elevations, so consult your dealer or Authorised Service Center about preparations. Failure to observe this may cause malfunctions. Notes on use In order to get the best picture quality If outside light or light from indoor lamps is shining onto the screen, the images projected will not have good contrast. Draw curtains or blinds over any windows and turn off any fluorescent lights near the screen to prevent reflection. Do not touch the surfaces of the lens with your bare hands. If the surface of the lens becomes dirty from fingerprints or anything else, this will be magnified and projected onto the screen. Moreover, when not using the projector, retract the lens and then cover it with the accessory lens cover. 10 About the screen If the screen you are using is dirty, damaged or discoloured, attractive projections cannot be obtained. Do not apply any volatile substances to the screen, and do not let it become dirty or damaged. Before carrying out cleaning and maintenance, be sure to disconnect the power cord plug from the wall outlet. Wipe the cabinet with a soft, dry cloth. If the cabinet is particularly dirty, soak the cloth in water with a small amount of neutral detergent in it, squeeze the cloth very well, and then wipe the cabinet. After cleaning, wipe the cabinet dry with a dry cloth. If using a chemically-treated cloth, read the instructions supplied with the cloth before use. Do not wipe the lens with a cloth that is dusty or which produces lint. If any dust or lint gets onto the lens, such dust or lint will be magnified and projected onto the screen. Use a blower to clean any dust and lint from the lens surface, or use a soft cloth to wipe off any dust or lint. Preparation Location and function of each part 0 Projector control panel (page 14) (2)Zoom ring (page 25) ©Focus ring (page 25) ©Air inlet ports Do not cover these ports. (D Projection lens (6) Lens cover (2) Remote control signal receptor (page 18) (DLeg adjuster buttons(UR) (page 24) These buttons are used to unlock the front adjustable legs. Press to adjust the angle of tilt of the projector. (DAir filter (page 44) ®Speaker 12 (T)Arr outlet port Do not cover this port. WARNING Do not bring your hands or other objects close to the air outlet port. • Heated air comes out of the air outlet port. Do not bring your hands or face, or objects which cannot withstand heat close to this port, otherwise burns or damage could result. (2) Remote control signal receptor (page 18) ©Connector panel (page 16) (4) Power input socket (AC IN) (page 24) The accessory power cord is connected here. Do not use any power cord other than the accessory power cord. ©MAIN POWER switch (pages 24 and 25) ©Card remote control unit holder (page 15) © Front adjustable legs(L/R) (page 24) ©Lamp unit holder (page 45) ©Security lock This can be used to connect a commercially-available theft-prevention cable (manufactured by Kensington). This security lock is compatible with the Microsaver Security System from Kensington. Contact details for this company are given below. Kensington Technology Group ACCO Brands Inc. 2855 Campus Drive San Mateo, CA 94403 USA Tel (650)572-2700 Fax (650)572-9675 NOTE: • During projection of an image, the cooling fan will operate, emitting a small noise as it operates. Turning the lamp on or off will cause this noise to increase a little. • By using the OPTION2 menu to set “LAMP POWER” to STANDARD, the operating sound of the fan can be reduced. (Refer to page 37....