Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
3. Press MENU button again to save. Contrast This adjustment allows you to adjust the contrast of the display. 1. Press the MENU button until CONTRAST shows in the display. 2. Use the CID (p or q) button to select level 1, 2, 3, or 4. 3. Press MENU button again to save. Local Area Code The telephone uses the programmed area codes to determine the number format to display when a valid Caller ID signal is received. Numbers that match the local area code are displayed as seven digits and are used for dialing back previous numbers. Entering your local area code will also help you immediately know if the call is local or long distance when viewing the CID records in the display. NOTE: If you make a mistake and want to start over, press the DEL button to delete all of the digits. 1. Press the MENU button until LOCAL AREA CODE shows in the display. 2. Use the CID (q) button to select the correct number or enter directly by using the number pad. 3. Use the CID (p) button to move to second and third digit locations to make your selections. 4. Press the MENU button to save. Telephone Operation Speakerphone For hands-free operation and convenience, this unit is equipped with a speakerphone. For best speakerphone performance, avoid the following: • Areas with high background noise. (The microphone might pick up these sounds and prevent the speakerphone from going into the receiving mode when you finish talking.) • Surfaces affected by vibration. • Recessed areas such as in a corner, under a cupboard, or next to a cabinet, which can generate an echo effect. Note the following guidelines when using the speakerphone: • The speakerphone works similar to a two-way radio in that you can only listen or talk at one time. • Stay reasonably close to the phone so that you can be clearly heard by the person to whom you are talking. • You can adjust the speaker volume by adjusting the VOLUME (p or q) buttons while the speakerphone is in use. • The speakerphone indicator illuminates when the speakerphone is in use. Placing a Call Handset 1. Pick up the handset and listen for a dial tone. 2. Dial the number you want to call. 3. When finished, hang up the handset. Speakerphone 1. Press the speaker button on the base and listen for a dial tone. 2. Dial the number you want to call. 3. When finished, press the speaker button to hang up. Answering a Call NOTE: Make sure the ringer switch is set to HI or LO, or the phone will not ring. The visual ring indicator will flash at all settings. Handset 1. When the phone rings, pick up the handset. 2. When finished, hang up the handset. Speakerphone 1. When the phone rings, press the speaker button to answer a call. 2. When finished, press the speaker button to hang up. You may switch between the speakerphone and the handset during the dialing process or anytime during a conversation. Speakerphone to Handset - Pick up the handset to disable the speakerphone. The speakerphone indicator turns off. Handset to Speakerphone - Press the speaker button, and then hang up the handset. The speakerphone indicator turns on and the handset is disabled. Volume You can control the volume of both the handset receiver and the speakerphone. While using the handset or speakerphone, you may adjust the volume to the desired listening level by using the VOLUME (p or q) buttons. Handset volume has 4 levels for adjustment and Speaker volume has 8 levels. Amplified Audio You may press the AMPLIFY button to temporarily boost the volume of the handset receiver during a call. To return to normal levels, press the button again. Volume levels will also return to normal when handset is replaced on base after call. The AMPLIFY button controls the increased volume level and tone equalizer of the handset. 1. Press the VOLUME (p or q) button to minimum, pick up the handset and press the AMPLIFY button to turn on the incoming voice amplifier. The indicator around the button illuminates. 2. Adjust the volume by pressing the VOLUME (p or q) button. When the AMPLIFY button is pressed, an extra level of amplified volume is added providing up to 40dB of gain and level control. In standard use, the amplifier turns off whenever you hang up the telephone. If you want the amplifier to turn on whenever you pick up the handset , slide the AMPLIFY Override switch located at the back of the unit to ON. NOTE: AMPLIFY feature is possible in both Handset and Speaker Mode. WARNING: This Product is designed for users with hearing disabilities and automatically amplifies the volume to the highest level when the AMPLIFY Override switch is set to “ON”. If you wish to prevent the automatic amplification, please turn the AMPLIFY Override switch located on the back of the set to “OFF”. Tone Equalizer The phone’s 3-band tone equalizer boosts the sound of the three frequency ranges ( 600Hz, 1.2KHz, 2.4KHz ) to compensate for the ear’s limited sensitivity in these ranges. 1. To turn on the equalizer, press the AMPLIFY button after you pick up the handset, or...