Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
These tools are illustrated on page 3. Pure Steam does not require detergents, chemicals or other cleaners, it cleans naturally with the action of steam. This powerful action also removes any traces of powder or liquid cleaners or detergents that have been previously used. SAFETY CUT- OUT A safety cut-out is fitted to prevent overheating of the element if water boils below the min. level. If unit stops boiling during use this may be the cause. Wait for 2 minutes before removing filler cap then re-fill with water. The cut-out will self reset and steam be produced again within 19 minutes. The cut-out will not protect the element if a part filled unit is tilted during use in a way which enables part of the element to be out of the water for longer than 15-20 seconds. CHANGING TOOLS Never remove the hose or change tools when the unit is plugged in. Wait 2 minutes after unplugging before changing tools. Screw the nut, which is on the end of the steam hose, onto the outlet of the tool -hand tight only. COMPONENT LIST a b c d e f g h i j k l a. Boiler F78 b Floor Cleaning Tool AC254 cTowel for Floor Cleaning Tool AC275 d Upholstery Cleaning Tool AC250 eTowel for Upholstery Cleaning Tool AC276 fWindow/Tile Cleaner AC258 g Jet Nozzle AC262 h Scraper AC21 i Brush AC25 j Long Handle (3 tubes) AC01 k Universal Handle AC302 l 3.65 metre Steam Hose ST94 m Castors (not shown) F17 n3 Metre Cord Set (not shown) B17 CASTORS The castors are packed separately. Turn the boiler upside down and insert the 3 castors. These should be pushed in hard until they stop. Once installed these remain in place permanently. ASSEMBLING THE ACCESSORIES The Universal Handle is used in conjunction with the Floor Cleaner, Upholstery Cleaner, Window / Tile Cleaner and Jet Nozzle. Align the outline triangle on the handle with the triangle on the accessory. Push the handle into the accessory and twist so that the solid triangles on the handle and accessory are aligned (Fig.1). Over time, you may find that your steam cleaning accessories become awkward to assemble to the universal handle. This is due to the steam reducing the lubrication properties of the ‘O’ ring seals. In this event, simply lubricate the ‘O’ ring seals as illustrated (Fig.2) using washing-up liquid or furniture polish. The Long Handle Attachment is designed to be used when cleaning floors or hard to reach areas. To assemble, pass hose through each of the long handle sections, in at the small end out at the large end. Screw the hose nut onto the universal handle and push the long handle tube sections together and onto the taper on the universal handle (Fig.3). You can use one, two or three sections of the long handle. Disconnect in reverse order. If you have any difficulty in disconnecting twist the handles apart. Fig.1 Assembling Universal Handle Fig.2 Seal Lubrication OPERATING INSTRUCTIONS Unscrew the filler cap and fill the boiler slowly until the float lifts up, approximately 4.5 ltrs. The maximum level will give you approx. 115 minutes of steam. DO NOT OVERFlLL. Connect the end of the steam hose to the threaded outlet on the boiler neck. DO NOT OVER TIGHTEN. Connect the power cord to the boiler and then connect to the power supply. Do not tilt in use. Sometime prior to the steam being produced a small amount of bubbling will occur at the tool. Be careful of any escaping hot water prior to steam emission. If the unit requires refilling, unplug cord, wait for 2 minutes to cool down, then refill as per the above instructions. BEWARE OF STEAM. When you have finished, allow any remaining water to cool down before emptying the boiler. Never store cold water in the unit and always disconnect the hose before storage. Storage should be in an upright position only. Filling Steam Unit The float rises when the boiler is full ACCESSORIES FLOOR CLEANER IMPORTANT: Some carpets have stain resistant treatments, which have varying active lives before breakdown. Accordingly it is best to try a small area of carpet that is normally unseen, then allow 24 hours to check whether the steam has any unusual effects on the carpet material. e.g. white streaks. DO NOT CONTINUE USE. - Check with your carpet supplier for further advice. Used correctly the Floor Cleaner will refresh your carpets by removing surface grime, pet hairs etc. leaving the carpet looking brighter. It is not a dirt extraction system, so cannot necessarily remove deep stains or grease. Attempting to make it do this by longer application of steam may result in watermarking or staining. Connect the Universal Handle and long handle to the Floor Cleaner head. Fit the cleaning towel to the head by placing the towel over the floor cleaner head and pulling drawstring tight. The drawstring can be secured at the back of the floor cleaner (Fig.4). Before using the Floor Cleaner, use a vacuum cleaner to pick up the larger dirt and grit particles. Having prepared the area, start the unit and wait for steam to appear at the accessory head. Now beg...