Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
1 Connect the AC adaptor. 2 Tuck the telephone line cord inside the wall mounting adaptor (1). Connect the telephone line cord (2). 3 Insert the hooks on the wall mounting adaptor into the holes (A) and (B) on the base unit. To power outlet Fasten the AC adaptor cord. Hook 1 2 A B B A Useful Information 4 Adjust the adaptor to hold the base unit, then push it in the direction of the arrow until it clicks into place. 5 Connect the telephone line cord. Mount the unit, then slide it down. L Raise the antennas. To remove the wall mounting adaptor While pushing down the release levers (1), remove the adaptor (2). 2 For assistance, please call 1-800-211-PANA (7262). Useful Information 40 For assistance, please call 1-800-211-PANA (7262). Belt clip You can hang the handset on your belt or pocket using the included belt clip. To attach the belt clip To remove the belt clip While pressing the top of the clip (1), pull the right edge in the direction of the arrow (2). Headset (optional) Connecting an optional headset to the handset allows hands-free phone conversations. Please use only a Panasonic headset. See page 5 for compatible headsets and ordering information. To connect an optional headset to the handset LModel shown is KX-TCA86. Note: LTo switch to the speakerphone, press {s}. To return to the headset, press {C}. 1 2 Headset jack Useful Information Error messages If the unit detects a problem, one of the following messages will be displayed on the handset. Display message Cause & solution Error!! L When you tried to register the handset, the handset and the base unit could not link for some reason, such as interference from electrical appliances. Move the handset and the base unit away from the electrical appliances and try again. No link to base. Move closer to base, try again. L The handset has lost communication with the base unit. Move closer to the base unit, and try again. L Confirm that the base unit’s AC adaptor is plugged in. L Raise the base unit antennas. L The handset’s registration may have been canceled. Re-register the handset (page 35). Phonebook full L There is no space to store new items in the phonebook. Erase unnecessary items (page 22). No items stored L Your phonebook or redial list is empty. Please lift up and try again. L A handset button was pressed while the handset was on the base unit. Lift the handset and press the button again. System is busy. Please try again later. L The handset has lost communication with the base unit. Move closer to the base unit and try again. Store VM access# L You have not stored the Voice Mail access number. Store the number (page 28). For assistance, please call 1-800-211-PANA (7262). Useful Information Troubleshooting General use Problem Cause & solution The unit does not work. L Make sure that the battery is installed correctly (page 10). L Check the connections (page 9). L Fully charge the battery (page 11). L Clean the charge contacts and charge again (page 11). L Unplug the base unit’s AC adaptor to reset the unit. Reconnect the adaptor and try again. L Re-install the battery (page 10) and fully charge it. The display shows “No L The handset is too far from the base unit. Move closer link to base. Move and try again. closer to base, try L Plug in the base unit’s AC adaptor. again.” and an alarm L Raise the base unit antennas. tone sounds. L If the above remedies do not solve the problem, the handset may have lost communication with the base unit. Register the handset again (page 35). I cannot hear a dial tone. L Confirm that the telephone line cord is connected (page 9). L Disconnect the unit from the telephone line and connect a known working telephone. If the working telephone operates properly, contact our service personnel to have the unit repaired. If the working telephone does not operate properly, contact your telephone company. Programmable settings Problem Cause & solution I cannot program items. L Programming is not possible while the handset is being used. L Do not pause for over 1 minute while programming. L Move closer to the base unit. While programming, the handset starts to ring. L A call is being received. Answer the call and start again from the beginning after hanging up. For assistance, please call 1-800-211-PANA (7262). Useful Information Making/answering calls, Paging Problem Cause & solution Static is heard, sound cuts in and out. Interference from other electrical units. L Move the handset and the base unit away from other electrical appliances. L Move closer to the base unit. L Raise the base unit antennas. L Turn on the clarity booster feature (page 19). L If your unit is connected to a telephone line with xDSL service, we recommend connecting a noise filter between the base unit and the telephone line jack. Contact your xDSL provider for details. The handset does not ring. L The ringer volume is turned off. Adjust it (page 31). I cannot make a call. L The dialing mode may be set incorrectly. Set the dial mode (page 33) to...