Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
To attain these results, you must adjust the pressure as low as possible. We recommend that you become familiar with your H.E.R.O. unit. Discuss with your dealer the useful accessory items he has to offer - various types of tips, extension poles for hard to reach areas, extra hose, etc. Use of accessory items is often the difference between a good job and an excellent one! NEW 1997 “B” SERIES HYDRAPULSE INTAKE ASSEMBLY BEGINNING WITH SERIAL NUMBER 190031 OPERATING INSTRUCTIONS WARNING Do not attempt to operate this machine until you have read and understood all safety precautions and operating instructions. Equipment and chemicals when used improperly can be dangerous. Your H.E.R.O. airless sprayer has been fully factory tested prior to shipment. BEFORE STARTING YOUR H.E.R.O. PUMP.... CHECK to ensure that the shipping seal has been removed from under the cap on the hydraulic tank. Hydraulic tank should be at least 3/4 full of H.E.R.O. LVO hydraulic fluid. CHECK all fittings and connections in the pump system, hose, and gun to ensure that they are tight. CHECK to ensure that there is a spray tip in the gun, and that the tip is the correct size for the coating you are to spray. ( There are various tips available, for each type of coating or configuration. See " Airless Spray Tip " on page 11 , for proper tip selection. CHECK to ensure that you have H.E.R.O. strainer bags, H.E.R.O. Wonder Wash, appropriate thinner for the paint, a waste container, and any other accessories you may require for the job. CHECK to ensure that you have adequate extension cord size and length if the machine cannot be situated immediately next to an electric outlet. Distances up to 50 feet require #12/3 wire grounded cord, up to 100 feet require #10/3 wire grounded cord. DO NOT exceed 100 feet of extension cord. If distance is greater, obtain and install extra length of H.E.R.O. airless spray hose. READ THIS MANUAL THOROUGHLY. H.E.R.O. INDUSTRIES LTD. 5 1100MD OWNERS MANUAL - “B” VERSION SETTING UP TO SPRAY 1. Remove unit from shipping carton. 2. Remove shipping seal from under hydraulic tank cap. 3. Re-position paint tank lid knob from the shipping position, on the underside of lid, and place on the lid top. 4. Attach paint hose to outgo tee (ref# 43) and gun to paint hose. NOTE; Spray tip and tip guard should be attached to gun prior to attaching to hose. 5. To assist in clean up, use and install paint tank plastic liners ( accessory item 5 GAL PL ). Line the inner sides of tank, ensuring that the liner does not block the tank screen in the bottom of the tank. Fold excess over the outside of tank. 6. Install strainer bag (accessory item 5GAL SB) in tank and secure with large rubber band ( accessory item 106 ). NOTE; Strainer bag must remain 4 inches from the bottom of tank. 7. Trigger gun to release any pressure in the unit. Use extreme caution to ensure that the gun is not directed towards anyone or any object which may be damaged. NOTE; Unit may contain storage solution. 8. To remove storage solution, add one gallon of thinner, compatible with the type of paint to be used, to the paint tank. 9. Turn pressure control knob (ref# 71) to lowest pressure setting. 10. Be sure motor switch is in "OFF" position. Plug unit into 115V, 15 amp., grounded circuit. NOTE; If using an extension cord, you MUST use a #12/3 wire grounded cord, up to 50 feet or #10/3 wire grounded cord, up to 100 feet. DO NOT EXCEED 100 FEET OF EXTENSION CORD. If distance is greater, purchase and install additional lengths of airless spray hose. 11. Turn motor switch "on" and increase pressure slowly. Trigger gun into a waste container. Continue spraying until pump runs dry and all thinner and holding solution has been removed. Keep pressure low. 12. Pour paint through strainer bag into paint tank. NOTE; Pour paint (particularly thick paints ) slowly, to allow paint to enter the intake hose while at the same time allowing air the opportunity to escape up the intake tube. Pouring paint in quickly can trap air in the intake tube ( air lock ) and make priming difficult. 13. Replace paint tank lid. Keep tank covered at all times to prevent contaminates from falling into the paint. 14. Increase the pressure, slowly at first, by turning the pressure control knob clockwise. Spray a test pattern. NOTE; Begin by spraying a test pattern onto old newspaper or other scrap material.Continue increasing the pressure until the spray pattern is uniformed from top to bottom, with no heavy areas. Secure pressure control setting, by turning the silver lock ring (ref# 73) counter clockwise until snugly against the face of the pressure control knob. If heavy areas are still visible at maximum pressure setting, thin the paint with the correct thinner, according to the paint manufacturer's recommendations. 70 43 Paint Tank outline Liner 5GAL PL Strainer bag 5GAL SB Rubber band 106 Paint in Air out H.E.R.O. INDUSTRIES LTD. 6 1100MD OWNERS MANUAL - “B” VERSION FLUSHING THE UNIT AT SHUTDOWN O...
Este manual também é adequado para os modelos :Armas - B series (696.93 kb)