Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
NOT to be used with fast drying paints and lacquers which will clog the opening in the air cap. INTERNAL MIX CAPS MUST BE USED WITH PRESSURE FEED OPERATION. External Mix—Used for quick drying, light bodied materials such as lacquers and synthetic enamels. Better for finer finish work. THESE CAPS CAN BE USED WITH EITHER SIPHON OR PRESSURE FEED. FAN DIRECTION The direction of the fan (horizontal or vertical) can be changed by loosening the lock ring and turning the air cap 90 degrees (See Figure 1). Hand tighten lock ring after adjustment. FLUID FEED MODEL KBS530 This model is capable of pressure or siphon feed. The gun is shipped in siphon feed mode but should be checked before use to ensure the desired feed method is selected. The feed method is easily changed by fully turning the side knob (See Figure 2). Model Descriptions (Cont.) • Adjusts for vertical or horizontal patterns. • May be used with a paint tank. General Safety 1. Read all manuals included with this product carefully. Be thoroughly familiar with the controls and the proper use of the equipment. 2. Follow all local electrical and safety codes as well as in the United States, the National Electrical Codes (NEC), Occupational Safety and Health Act (OSHA) and the Environmental Protection Agency (EPA). Safety glasses and ear protection must be worn during operation. Use a face mask/respirator and protective clothing when spraying. Always spray in a well ventilated area to prevent health and fire hazards. Refer to Material Safety Data Sheets (MSDS) of spray material for details. Never spray closer than 25 feet to the compressor! If possible, locate compressor in separate room. Never spray into the compressor, compressor controls or the motor. 3. Do not smoke or eat when spraying paint, insecticides, or other flammable substances. Do not spray flammable materials in vicinity of open flame or near ignition sources. Motors, electrical equipment and controls can cause electrical arcs that will ignite a flammable gas or vapor. Never store flammable liquids or gases in the vicinity of the compressor. ! WARNING ! DANGER ! WARNING ! WARNING 4. When spraying and cleaning, always follow the instructions and safety precautions provided by the material manufacturer (Refer to MSDS). Do not spray acids, corrosive materials, toxic chemicals, fertilizers or pesticides. Using these materials could result in death or serious injury. 5. Keep visitors away and NEVER allow children or pets in the work area. Never aim or spray at yourself or anyone else or serious injury could occur. 6. Always work in a clean environment. To avoid injury and damage to the workpiece, do not aim the spray gun at any dust or debris. Do not use pressure that exceeds the operating pressure of any of the parts (hoses, fittings, etc.) in the painting system. Keep hose away from sharp objects. Bursting air hoses may cause injury. Examine air hoses regularly and replace if damaged. 7. Always use a pressure regulator on the air supply to the spray gun. Failure to install appropriate water/oil removal equipment may result in damage to machinery or workpiece. Do not misuse this product. Excessive exposure to vibration, work in awkward positions, and repetitive work motions can cause injury to hands and arms. Stop using any tool if discomfort, numbness, tingling, or pain occur, and consult a physician. CALIFORNIA PROPOSITION 65 You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry. This dust often contains chemicals known to cause cancer, birth defects, or other reproductive harm. Wear protective gear. ! DANGER ! WARNING NOTICE ! CAUTION ! WARNING ! WARNING ! WARNING MANUAL 2 23 Sp General Purpose Spray Guns Modelo KBS530 Guia de Diagnostico de Averias Problema Posible(s) Causa(s) Accion a Tomar El patron de rocio es muy pequeno El patron de rocio es inadecuado Exceso de rocio Fuga por la tuerca de control de fluido Fuga por el envase y la tapa del envase Cascara de naranja (apariencia de ondulacion aspera semejante a una cascara de naranja real) Chorreos y depresiones Superficie con acabado moteado y tosco 1. Acumulacion de material seco en los orificios de la tapa de aire 2. Material aglutinado 3. Insuficiente cantidad de material 4. Insuficiente presion de fluido 1. El material esta muy espeso 2. La tapa de aire esta sucia 3. Esta aplicando mucho material 4. El patron es muy ancho 1. Demasiada presion de aire para el tipo de material que esta aplicando 2. El material esta muy diluido 1. El empaque esta muy flojo 2. El empaque esta desgastado o reseco 1. El empaque del envase esta mal colocado 2. El envase no esta bien apretado 1. El material se esta secando muy rapido 2. Pistola muy lejos de la superficie 3. Material muy espeso 1. Material muy diluido 2. La pistola se esta moviendo muy lentamente 3. Flujo excesivo de material 4. Pistola muy cerca de la superficie 1. Demasiado solvente 2. Tecnica deficiente de rociado 1. Lim...