This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

Secure the sensor in the desired location using the wall mount hole or double sided adhesive tape. For best results: • Place the sensor within 30 m (100 ft) of the main unit. • Place the sensor out of direct sunlight and moisture. • Position the sensor so that it faces the main unit, minimizing obstructions such as doors, walls and furniture. • Place the sensor in a location with a clear view to the sky, away from metallic / electronic objects. • Position the sensor close to the main unit during

ALARM ON/OFF slide switch: enable or disable alarm 3. SLEEP: activate sleep timer 4. 1, 2, 3, 4: preset radio stations 5. RADIO ON/VOL : turn on radio; increase radio volume 6. RADIO OFF/VOL : turn off radio; decrease radio volume BOTTOM VIEW 1 23 4 56 7 8 9 1. SNOOZE buttons: snooze alarm; turn on projection 2. UP/TUNE +: increase value during setting; increase frequency during radio scan 3. DOWN/TUNE -: decrease value during setting; decrease frequency during radio scan 4. Battery compartment

2 Front View....................................................................... 2 Top View......................................................................... 3 Bottom View.................................................................... 3 Solar Panel...................................................................... 4 Remote Sensor............................................................... 4 Getting Started.................................................................. 4 S

• Do not overcharge the batteries. Bac kup power 1 piece AAA battery In the case when the rechargeable battery is flat or nearly flat or when the solar panel has been detached, the AAA battery can act as backup power supply for the main unit. 1. Remove the battery compartment located at the base of the unit. 2. Insert the battery, matching the polarity. 3. Press RESET after each battery change. Power adaptor (not included) The adaptor powers the unit and can also be used for charging the recharg

Together we can improve the world we live in. Over view Front View 1 10 11 12 13 14 15 16 2 3 4 5678 9 1. : Remote sensor reception indicator and outdoor channel selected 2. Outdoor temperature 3. Indoor temperature 4. Weather forecast 5. : Clock signal reception indicator 6. : Alarm time is displayed 7. : Daily alarm is On 8. AM / PM 9. Rechargeable battery status LED indicator 10. : Outdoor remote sensor battery low 11 . : Main unit back-up batteries low / no battery 12. : AC adaptor connected

Please keep this manual for instructions and information you should know about. CLOCK OVERVIEW FRONT VIEW 1 5 2 6 3 4 1. SNOOZE: Snooze alarm; activate backlight; rotate dual line projection display by 180° 2. ALARM: View alarm status; set alarm 3. CLOCK: Change display; set clock 4. / : Toggle setting options; activate / deactivate clock reception 5. Projector (LED Aperture) 6. TEMP: Toggle in / out temperature settings BACK VIEW 1 3 4 5 6 2 7 8 9 1. FOCUS: Focus the projected image 2. Battery

32 Bottom View........................................................... 32 LCD Display........................................................... 32 Getting Start.............................................................. 32 Replacing Lamp..................................................... 32 Connect to Power Source...................................... 3 3Clock.......................................................................... 53 Manually Set Clock.................................

2 Front view ........................................................................ 2 Back view ........................................................................ 3 LCD display symbols ....................................................... 3 Safety and care instructions ............................................. 4 Safety precautions ........................................................... 4 Caring for your product .................................................... 4 Getting star

Press and hold CLOCK ALARM for 2 seconds to enter the Alarm Setting Mode. 2. Alarm 1 will start flashing. Use the and buttons to toggle between alarm 1 and 2. Then press CLOCK ALARM to select alarm 1 or 2. The hour will start flashing. 3. Enter the value by pressing the or buttons. 4. Confirm the entry by pressing the CLOCK ALARM button and move on to the next setting. 5. Repeat (3 and 4) to set alarm 1 / alarm 2 - minute, melody alarm and / or vibration alarm (optional). If the melody alarm is