Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
950 • EN60950 • CE – EN55022 Class B – EN50082-1 Canadian EMI Notice This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe A respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada. European Notice Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the commission of the European Community. Compliance with these directives implies conformity to the following European Norms: • EN55022 (CISPR 22) - Radio Frequency Interference • EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic Immunity • EN60950 (IEC950) - Product Safety Five-Year Limited Warranty MiLAN Technology warrants to the original consumer or purchaser that each of its products, and all components thereof, will be free from defects in material and/or workmanship for a period of five years from the original factory shipment date. Any warranty hereunder is extended to the original consumer or purchaser and is not assignable. MiLAN Technology makes no express or implied warranties including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose, except as expressly set forth in this warranty. In no event shall MiLAN Technology be liable for incidental or consequential damages, costs, or expenses arising out of or in connection with the performance of the product delivered hereunder. MiLAN Technology will in no case cover damages arising out of the product being used in a negligent fashion or manner. Trademarks MiLAN Technology™ is a trademark of MiLAN Technology. All other products and brands are the trademarks of their respective holders. All rights reserved. To Contact MiLAN For prompt response when calling for service information, have the following information ready: • Product serial number and rev. • Date of purchase • Vendor or place of purchase You can reach MiLAN technical support at 408/744-2751 Or E-mail at: support@milan.com Address: 1299 Orleans Drive Sunnyvale, CA 94089 Voice: 408/744-2775 Fax: 408/744-2793 Web: Installation Guide: MIL-140TRM MIL-140CRM and MIL-140TRM 10BASE-FL to 10BASE-T Media Converter for MiLAN's Media Conversion System Thumbscrews TP FX 10BASE-FL ACT ACT MDI-X MDI TP FX TX RX MIL-10BASE-T LINK LINK 140TRM Installation Guide This guide includes the following: • “Introduction” on page 2 • “Installation” on page 3 • “MDI-X/MDI” on page 3 • “Link Sentry Configuration” on page 5 • “Indicators” on page 6 ® Copyright 1998 MiLAN Technology Printed in the USA P/N: 90000111 Rev. B About this Manual This document covers both the MIL-140CRM and the MIL-140TRM media converter modules. The terms “MIL-140” and “converter” are used throughout this document to describe these devices. Introduction The MIL-140 converters are part of a series of modules designed to be installed into MiLAN's Media Conversion System. These half-/full-duplex devices convert Ethernet optical signals to electrical and vice- versa. The converter has a signal capability of transmitting up to 2 km (subject to fiber budget and collision domain restrictions). This module also has the Link Sentry feature. Features • One RJ-45 (UTP) connector • One multi-mode, SC or ST fiber connector • Link Sentry feature • Diagnostic LEDs • Management ready–supplied by MiLAN’s optional SNMP modules (MIL-4650 and MIL-4655) • Power supply equipped on the rack mount chassis Installation Guide: MIL-140TRM 1234 5 78 6 Figure 2. RJ-45 Pinouts Fiber Specifications: SC and ST Connector • 850 nm multi-mode fiber • 62.5/125 multi-mode fiber • Launch power: -19 dBm • Receive sensitivity: -34 dBm Operating Conditions Table 2: Recommended Operation Conditions Parameters Minimum Maximum Operating Temperature +5° C +50° C Humidity: Non-condensing 10% 95% Signal Output Load 35 ohm 75 ohm Supply Voltage 4.75 V 5.25 V 2 7 Indicators There are four LEDs, including: • TP/ACT: Receiving packets from the 10BASE-T port • TP/LINK: There is an active connection on the 10BASE-T port • FX/LINK: There is an active connection on the 10BASE-FL port • FX/ACT: Receiving packets from the 10BASE-FL port Specifications RJ-45: MDI • Pin 1 = Transmit Data + • Pin 2 = Transmit Data • Pin 3 = Receive Data + • Pin 6 = Receive Data RJ- 45: MDI-X • Pin 1 = Receive Data + • Pin 2 = Receive Data • Pin 3 = Transmit Data + • Pin 6 = Transmit Data Installation Guide: MIL-140TRM Installation Do the following to install the MIL-140 into a rack mount chassis: 1. Make any configuration changes to the module (i.e., DIP switch settings). 2. Remove the screws securing the faceplate and remove it from the chassis. 3. Slide the module into the slot through the guide rails. 4. Insert the module into the card-edge connector (port bay). Make sure it is seated firmly. 5. Secure the module with the two thumbscrews located on the faceplate of the unit. The unit is now ready for net...