Assessments - 4, GPA: 5
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
(The factory-set lowpass filter frequency is 100 Hz.) See “Setting speakers and their sizes” for changing the speaker size to “LARGE ”. RQT8549 Confirming audio output from speakers and adjusting volumes Through these steps, you make sure each of the connected speakers makes audio output. Adjust the output level from each speaker and the output level from the front speakers to achieve balance in the listening- viewing position. 1 1 When only the SPEAKERS A When SPEAKERS A and SPEAKERS B Select [SPEAKERS A]. setting is selected settings are selected SPEAKERS A SPEAKERS or A Press A B SPEAKERS • If you select SPEAKERS B only, the test signal will not be output. When using a BI-WIRE connection (a page 11) Select “YES ” in “Setting bi-wiring connections” (a page 31). SPEAKERS SPEAKERS Press AB or A B SPEAKERS BI-WIRE Connections 2 2 Check the test signal output. Press TEST • A test signal is output from one speaker at a time for two seconds in the following order. L > C > R > RS > SBR > SBL > LS > SUBW or L > C > R > RS > SB > LS > SUBW (When you connect one surround back speaker only) • Speakers not connected (a pages 11 and 14) and others manually set as absent (a page 31) do not produce the test signal. 3 3 Adjust the volumes of front speakers to the normal listening level. 4 4 Press Select a speaker for adjustment. VOLUME LEVEL Press and select a speaker. 5 5 Adjust the volume of the selected speaker. Press Repeat steps 4 and 5 to adjust the level of each speaker. Stop the test signal. Press TEST How speakers are displayed L : Front left C : Center R : Front right RS : Surround right LS : Surround left SBR : Surround back right SBL : Surround back left SB : Surround back (If you connect one surround back speaker) SUBW : Subwoofer Volume range: -- dB (minimum), -79 dB to 0 dB (maximum) Adjustment range: -10 dB to +10 dB (Factory setting: 0 dB) SUBW only: MIN (minimum) - 1 to 19 - MAX (maximum) (Factory setting: 10 ) • Only the adjusted speaker produces the test signal in steps 4 and 5. Connected speakers start producing the test signal again in the above order 2 seconds after both steps. Before playback 15 RQT8549 16 Basic playback 1 Turn the unit on. Press The [MULTI CH SURROUND] indicator comes on (Factory setting). • The standby indicator [^] goes off when you turn the unit on. Do not forget to perform speaker detection when you play a source on the unit for the first time or when you change the number of connected speakers (a page 14). 2 Select [SPEAKERS A]. Press Press [SPEAKERS B] when you use SPEAKERS B. (Playback becomes 2-channel only when you use the SPEAKERS B setting.) When using a BI-WIRE connection (a page 11) Select “YES ” in “Setting bi-wiring connections” (a page 31). Press or 3 Turn [INPUT SELECTOR] and choose an input source. Turn Input sources: TUNER FM, TUNER AM, CD, TV/STB, DVD, DVR, VCR (video recorder), AUX (external input) • If “DVR ” is selected, “DVD RECORDER ” scrolls once on the display. You can also choose the input selector using the remote control (a page 4). Using a DVD recorder with built-in VCR (a page 9) • To play a DVD: Select “DVR ”. • To play a video cassette: Select “VCR ”. 4 Play back the selected input source. The unit produces 2-channel stereo sounds when you switch off [MULTI CH SURROUND]. Press [MULTI CH SURROUND] again when you wish to use the surround effect. • The unit stores setting about MULTI CH SURROUND use for each input source. The multi-channel surround effect activates whenever you play a multi-channel source. • You can start 2-channel mix (2CH MIX) by switching MULTI CH SURROUND off while playing a multi-channel source (excluding DVD- Audio sources that do not allow down-mixing). 2-channel mix goes off when you turn the unit off or when you change the input source. 5 Adjust the volume. Turn Volume range: -- dB (minimum), –79 dB to 0 dB (maximum) When you finish listening Be sure to reduce the volume and press [8, POWER] to turn the unit to standby. AUTO SPEAKER DETECTOR ADVANCED DUAL AMP BI-AMP WIRELESS READY POWER SPEAKERS A B AUTO SPEAKER DETECTOR MULTI CH SURROUND AUX S VIDEO IN VIDEO IN L AUDIO IN R MENU SETUP RETURN INPUT SELECTOR ENTER VOLUME HDMI TUNE POWER SPEAKERS A B MULTI CH SURROUND INPUT SELECTOR VOLUME [ ] POWER MULTI CH SURROUND Note SPEAKERS A A SPEAKERS Note SPEAKERS A SPEAKERS B A B SPEAKERS BI-WIRE INPUT SELECTOR Note Note VOLUME 16 Basic playback 1 Turn the unit on. Press The [MULTI CH SURROUND] indicator comes on (Factory setting). • The standby indicator [^] goes off when you turn the unit on. Do not forget to perform speaker detection when you play a source on the unit for the first time or when you change the number of connected speakers (a page 14). 2 Select [SPEAKERS A]. Press Press [SPEAKERS B] when you use SPEAKERS B. (Playback becomes 2-channel only when you use the SPEAKERS B setting.) When using a BI-WIRE connection (a page 11) Select “YES ” in “Setting bi-wiring connections” (a page 31). Press or 3 Turn [INPUT SELECTOR] ...