Assessments - 5, GPA: 3.2
(
)
)
|
Facilidade de uso
z To listen directly to the input signal Press SOURCE DIRECT so that the indicator lights up. Since the circuits of TONE controls, BALANCE control, LOUDNESS button, and SUBSONIC button are bypassed, you cannot adjust bass, treble, the balance, reinforce the bass and treble, or reduce subsonic noise components while listening to a source directly. Note Avoid high speaker output at which the sound is distorted. High-frequency distortion may damage the tweeters. 1 1 Press POWER to turn on the amplifier and turn VOLUME fully anticlockwise to prevent damaging the speakers with excessive output. The PROTECTION indicator lights up, then goes off. 2 2 Turn on the programme source you want to listen to. 3 3 Set INPUT SELECTOR to the respective programme source. The indicator for the programme source lights up. To listen to a Turn INPUT SELECTOR for Record PHONO Radio broadcast TUNER Compact disc or SACD SACD/CD Source connected to AUX AUX Source connected to: —TAPE1/DAT TAPE1/DAT —TAPE2/MD TAPE2/MD 5 5 4 4 Start the programme source. Adjust the volume by turning VOLUME. To Press or turn Adjust the bass BASS Adjust the treble TREBLE Adjust the balance BALANCE Reinforce the bass and treble at low LOUDNESS listening level Reduce subsonic noise components SUBSONIC created by warped records, etc. 7 Basic Basic Operations Basic Operations z What is the Enhanced Other Networks (EON)? One convenient RDS service is “Enhanced Other Networks” (or “EON”). This allows the unit to automatically switch to a programme type of your choice when one starts in your broadcast area. To receive the Enhanced Other Networks (EON) programmes When your amplifier is connected to a Sony tuner with the EON CONTROL system, the amplifier switches to any EON programme that is broadcast in your EON area, and switches back to the last selected programme source when the programme ends. TA-FB940R TA-FB740R EON LINK EON LINK PROTECTION PHONES SPEAKERS A •• • • OFF A+B –10 +10 TONE SUBSONIC EON LINK B SOURCE • ••TAPE1 TAPE2 BASS 0 • • •–10 +10 TREBLE 0 • • •LEFT RIGHT BALANCE • • • TAPE MONITOR TAPE1/DATEON LINK SACD/CD TUNER PHONOAUXTAPE2/MD LOUDNESS . ON . OFF . ON . OFF POWER INPUT SELECTOR PROTECTION PHONES SPEAKERS A 0 BASS •OFF A+B –10 +10 TONE INPUT SELECTOR LOUDNESS . ON . OFF B SOURCETAPE10 TREBLE • –10 +10 • BALANCE TAPE MONITOR SACD/CD TUNERAUX TAPE2/MD TAPE1/DAT PHONO • LEFT RIGHT EON LINK POWER 1 Make sure that the amplifier and the tuner are connected through the EON CONTROL terminals (see page 5). 2 Press EON LINK so that the indicator lights up. Whenever an EON programme starts on the radio frequency that your tuner is set to, you will receive it. To cancel EON reception Press EON LINK again so that the indicator goes off. Notes •If you select another programme source while receiving an EON programme, EON reception ends. However, as long as the EON LINK indicator lights up, you can receive EON programmes automatically. •Make sure to cancel EON reception before starting to record since an EON programme may interfere with your recording. •If you activate the Tape Monitor function (see page 9) while the EON LINK indicator is lit, the indicator goes off and you cannot receive EON programmes. If this happens, deactivate the Tape Monitor function so that the indicator lights up again. Basic Operations Basic Operations Recording TA-FB940R TA-FB740R 1 3 1 3 PROTECTION PHONES SPEAKERS A •• • • OFF A+B –10 +10 TONE SUBSONIC EON LINK INPUT SELECTOR VOLUME SOURCE DIRECT 0 10 B SOURCE • ••TAPE1 TAPE2 BASS 0 • • •–10 +10 TREBLE 0 • • •LEFT RIGHT BALANCE • • • TAPE MONITOR TAPE1/DATEON LINK SACD/CD TUNER PHONOAUXTAPE2/MD LOUDNESS .ON .OFF .ON .OFF POWER PROTECTION PHONES SPEAKERS A 0 BASS •OFF A+B –10 +10 TONE SUBSONIC INPUT SELECTOR VOLUME SOURCE DIRECT EON LINK 0 10 .ON .OFF LOUDNESS .ON .OFF B SOURCETAPE10 TREBLE • –10 +10 • BALANCE TAPE MONITOR SACD/CD TUNERAUX TAPE2/MD TAPE1/DAT PHONO • LEFT RIGHT POWER z You can record the same source on two recording components at the same time z You can monitor the recorded sound (Tape Monitor function) You can monitor the recorded sound if the tape deck you are recording on has separate playback and recording heads. To monitor the sound, set TAPE MONITOR to TAPE1 or TAPE2. Note that on the TA-FB740R, you can monitor the only sound being recorded from the TAPE1/DAT jacks. Note Before you begin recording, press the EON LINK button to turn off the EON LINK indicator (see page 8). 1 1 Press POWER to turn on the amplifier. 2 2 Turn on the programme source you want to record. 3 3 Select the programme source that you want to record by turning INPUT SELECTOR. The indicator for the programme source lights up. To record a Set INPUT SELECTOR to Record PHONO Radio broadcast TUNER Compact disc or SACD SACD/CD Source connected to AUX AUX Source connected to: —TAPE1/DAT TAPE1/DAT —TAPE2/MD TAPE2/MD 4 4 Prepare the recording component for recording, then start recording. 5 5 Start playing the programme source. Basic 9 Addition...
Este manual também é adequado para os modelos :receptor e amplificador - TA-FB740R (121.87 kb)