Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
When using the remote, point it at the remote control sensor gon the amplifier. z When to replace batteries With normal use, the batteries should last for about 6 months. When the remote no longer operates the amplifier, replace all the batteries. Notes • Do not leave the remote near an extremely hot or humid place. • Do not drop any foreign object into the remote casing, particularly when replacing the batteries. • Do not expose the remote sensor to direct sunlight or lighting equipment. Doing so may cause a malfunction. • If you don’t use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. Getting Started Getting Started Hookup Overview The amplifier allows you to connect and control the following audio components. Follow the hookup procedure indicated for each component that you want to connect. To learn the location and name of each jack, see “Rear Panel Descriptions” on page 11. DAT deck Tape deck Tuner Speaker (L) Speaker (R)TV or video deck MD deck Turntable SACD CD player PROTECTION PHONES SPEAKERS A •• • • OFF A+B –10 +10 TONE SUBSONIC EON LINK INPUT SELECTOR VOLUME SOURCE DIRECT 0 10 B SOURCE • ••TAPE1 TAPE2 BASS 0 • • •–10 +10 TREBLE 0 • • •LEFT RIGHT BALANCE • • • TAPE MONITOR TAPE1/DATEON LINK SACD/CD TUNER PHONOAUXTAPE2/MD LOUDNESS . ON . OFF . ON . OFF POWER Before you get started • Turn off the power to all components before making any connections. • Do not connect the mains leads of the various components until all connections are completed. • Use the audio connecting cords supplied with each component for hooking up with the amplifier. Purchase and use optionally available cords as required. • Be sure to make connections firmly to prevent hum and noise. • When connecting an audio connecting cord, be sure to match the R (right) and L (left) jacks of the amplifier to the R and L jacks on the other components. Audio Component Hookups Overview Here you learn how to connect your audio components to the amplifier. PHONO y AUX TAPE1/DAT EON CONTROL INTUNER TAPE2/MD SACD/CD SPEAKERS EON CONTROL R B A L+ +– – R L+ +– – TAPE1/DAT L REC OUT IN IMPEDANCE USE 4–16W A+B USE 8–16W BI WIRE USE 4–16W IN R L R TAPE2/MD REC OUT IN AUX IN SACD/ CD IN TUNER IN L R PHONO IN SIGNAL GND y What cords will I need? Audio connecting cord (not supplied) (2 for each tape deck, DAT deck, or MD deck; 1 for other components) White (L) White (L) Red (R) Red (R) Hookups The arrow .indicates signal flow. SACD/CD player Amplifier SACD/CD player L OUTPUT L .. R R IN SACD/ CD Tuner Amplifier Tuner L OUTPUT L .. R R IN TUNER 4 Getting Started Getting Started Tape deck, DAT deck, or MD deck Amplifier Tape deck L .. R .. OUTPUT L R INPUT Use the configuration above to connect the OUTPUT and INPUT jacks of: —a tape deck or DAT deck to the TAPE1/DAT jacks. —a tape deck or MD deck to the TAPE2/MD jacks. Turntable Amplifier Turntable SIGNAL GND y L .. R INOUT TAPE1/DAT PHONO IN Note To prevent hum, connect the earth lead to SIGNAL GND (y) on the amplifier. TV or video deck Amplifier TV or video deck L OUTPUT L .. R R IN AUX EON CONTROL Amplifier Tuner .EON CONTROL IN EON CONTROL OUT If your tuner is equipped with an EON CONTROL OUT terminal, connect it to the EON CONTROL IN terminal on the amplifier to allow use of the EON (Enhanced Other Networks) function of the RDS (Radio Data System) (see page 8). Speaker System Hookups Overview Here you learn how to connect speakers to the amplifier. You can connect two pairs of speakers, SPEAKERS A and B. Note that the SPEAKERS A terminals comprise the bottom row of the SPEAKERS terminals. SPEAKERS A SPEAKERS B SPEAKERS EON CONTROL R B A L+ +– – R L+ +– – TAPE1/DAT L REC OUT IN IMPEDANCE USE 4–16W A+B USE 8–16W BI WIRE USE 4–16W IN R L R TAPE2/MD REC OUT IN AUX IN SACD/ CD IN TUNER IN L R PHONO IN SIGNAL GND y What cords will I need? Speaker cord (not supplied) (1 for each speaker) (+) (+) (–) (–) Twist the stripped ends of the cord about 10 mm. Be sure to match the speaker cord to the appropriate terminal on the components: + to + and – to –. If the cords are reversed, the sound will be distorted and will lack bass. Hookups ] }b ] } Getting Started Getting Started Connecting to bi-wire system speakers Since the two pairs of speaker terminals on your amplifier, SPEAKERS A and B, can provide simultaneous speaker output, you can use them to connect a bi-wire speaker system. To drive both speaker systems simultaneously, set SPEAKERS to A+B. To select the speaker system A or B Set SPEAKERS to A or B. To drive both speaker systems simultaneously, set SPEAKERS to A+B. Note Use speakers with a nominal impedance of 4 to 16 ohms. When outputting at the same time to two speaker systems, use speakers with a nominal impedance of 8 to 16 ohms. Mains Lead Hookups Connecting the mains lead Connect the mains lead from this amplifier and from your audio/video components to wall outlets. Note Separate the mains lead, audio connecting cords a...
Este manual também é adequado para os modelos :receptor e amplificador - TA-FB940R (121.87 kb)