SPECIFICATIONS Model 2012NB Cutting width 304 mm (12”) Max. cutting depth 3.0 mm (1/8”) of stock width less than 150 mm (5-7/8”) 1.5 mm (1/16”) of stock width from 150 mm (5-7/8”) to 240 mm (9-1/2”) 1.0 mm (3/64”) of stock width from 240 mm (9-1/2”) to 304 mm (12”) Feed rate /min 8.5 m (27.9 ft.) /min. Table size (W x L) 304 mm x 771 mm (12” x 30-3/8”) No load speed (RPM) 8,500 /min. Dimensions ( W x L x H ) 483 mm x 771 mm x 401 mm (19-1/64” x 30-3/8” x 15-25/32”) Net weight 27 kg (59.5 lbs) •

No. No. Used Description No. No. Used Description 1 911001-2 2 P.H. Screw M3x6 (With Washer) 51 251246-3 4 (+) P.H. Screw M4x5 2 * 2 P.H. Screw M4x14 52 342430-2 2 Adjust Plate 3 911228-4 2 P.H. Screw M5x18 (With Washer) 53 911226-8 2 P.H. Screw M5x18 (With Washer) 4 931106-2 2 Rivet 0-5 54 323001-4 1 Drum Rear Shaft 5 * 1 Switch 55 253139-0 1 Flat Washer 8 6 * * P.H. Screw M4x6 (With Washer) 56 211032-4 1 Ball Bearing 608ZZ (Old 210011-9) 7 682502-4 1 Cord Guard 8-85 57 961004-6 1 Retaining Rin

13. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. 14. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. Ordinary eye or sun glasses are NOT eye protection. Tool Use and Care 15. Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work

CARBON BRUSH REPLACEMENT 0 Replace carbon brushes when they wear I_----- down to about 6mm (1/4") or sparking will occur. Both brushes should be changed at ! the same time. L 9 0 To replace carbon brushes, use the (-1 minus screwdriver equipped to remove the holder cap on the motor housing. Then replace the brush. HOW TO USE THE SHARPENING HOLDER 0 First, loosen the 2 wing nuts on the holder and insert blades Aand B as in figure at right, so that they contact side C and D. Then tighten wing nuts

IO.Stop operation immediately if you notice anything abnormal. 11. Always switch off and wait for blades to come to a complete stop before adjusting any parts, cleaning out chips or approaching the blade. 12. Never stick your finger into the chip chute. Chute may jam when cutting damp wood. Turn off the planer-jointer and then clean out chips with a stick. 13. Do not touch blades right after operation, they may be extremely hot and could burn your skin. 14. Don't abuse cord. Never yank cord to d

5. Hold the tool firmly with both hands. 6. Keep hands away from rotating parts. 7. Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced blade. 8. Make sure the blade is not contacting the workpiece before the switch is turned on. 9. Wait until the blade attains full speed before cutting. IO. Keep at least 200 mm (8”)away from the tool at all times. 11. Always switch off and wait for the b

® TtiakixCL Woodworking G 12-1/4" Planer J(P31^« Precision Engineered for an Even Cut Every Time • Powerful 15 AMP motor with 12,000 RPM • Poly"V"belt designed with grooves efficiently transfers power from the motor to the blades • Large ejection chute for high rate of chip discharge • Front roller for easy moving over rough materials • Externally accessible brushes for easier serviceability • Large,conveniently located depth setting knob for easy adjustment MODEL KP312 INCLUDES: So

A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user — as well as damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate-rating is harmful to the motor. ADDITIONAL SAFETY RULES 1. Rags, cloth, cord, string and the like should never be left around the work area. 2. Avoid cutting nails. Inspect for and remove all nails from the workpiece before operation. 3. Handle the blades v

For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. 1 2 1 2 Pins 2. Edge fence (Guide rule) 1 23 1. Rear base 2. Foot 3. Planer blade 003873 Edge fence (Guide rule) Edge fence is useful for minimizing a short run of cut by cutting in a uniform width. The edge fence (guide rule) is provided on the side of the tool. Press two pins for the edge fence (guide rule) so that the ed