If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful to the motor. ADDITIONAL SAFETY RULES 1. Rags, cloth, cord, string and the like should never be left around the work area. 2.Avoid cutting nails. Inspect for and remove all nails from the workpiece be- fore operation. 3.Handle the blades very carefully. 4. Be sure the blade installation bolts are securely tightened before operation. 5.Hold the tool firmly with both hands. 6. Keep han

2. Do not perform jointing operations on material shorter than 140 mm (5-112 inches), narrower than 19mm (3/4 inch), or less than 12.7 mm (112 inch) thick. 3.Do not perform planing operations on material shorter than 140 mm (5-1/2 inches), narrower than 19 mm (314 inch), wider than 155 mm (6-118 inches) or thinner than 12.7 mm (1/2 inch). 4. Support the workpiece adequately at all times during operation. 5. Do not back the work toward the infeed table. 6. Always use hold-downlpush blocks for joi

Cause: One or both blades fails to have edge parallel to rear base line. Cause: One or both blade edges fails to protrude enough in relation to rear base line. Cause: One or both blade edges protrudes too far in relation to rear base line. Dust bag (accessory) 1. Dust bag 2. Chip discharge opening 2 1 007687 Attach the dust bag onto the chip discharge opening. The chip discharge opening is tapered. When attaching the dust bag, push it onto the chip discharge opening firmly as far as it will go t

A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user — as well as damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate-rating is harmful to the motor. ADDITIONAL SAFETY RULES 1. Rags, cloth, cord, string and the like should never be left around the work area. 2. Avoid cutting nails. Inspect for and remove all nails from the workpiece before operation. 3. Handle the blades v

IO.Stop operation immediately if you notice anything abnormal. 11. Always switch off and wait for blades to come to a complete stop before adjusting any parts, cleaning out chips or approaching the blade. 12. Never stick your finger into the chip chute. Chute may jam when cutting damp wood. Turn off the planer-jointer and then clean out chips with a stick. 13. Do not touch blades right after operation, they may be extremely hot and could burn your skin. 14. Don't abuse cord. Never yank cord to d

ACCESSOR IES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments hsould be used only in the proper and intended manner. 0 Replacement blades Sprocket set 400 mm (15-3/4”1 (For Low Speed Feed) Part No. 731024-2/ Part No. 191440-4 ;fitA& .. 0 Planer stand Part No.122192-3A 15 Jan -08-'96 Us MODEL 2040 c c 16 17 7 8 9

It chamfers up to 5.6 mm (7/32")in a single pass. I groove I I Front base I I ASSEMBLY Dust bag Install the dust bag on the nozzle of the tool. When installing it, push the bag's entry port toward the nozzle as far as it will go to prevent it from coming off during operation. For the best results, empty the dust bag when it becomes about half full. Remove the dust bag from the tool and pull out the fastener. NOTE: If you connect a Makita vacuum cleaner Model 406 to this tool, more efficient and

CAUTION : I Mini planer blade Drum s- \ Groove Bolt Drum - Plarier blade yq Drum cover ' I Adjusting plate Inside edge of gauge plate Blade edge Planer blade Adjusting plate Back side of -- gauge base Gauge plate Tighten the blade installation bolts carefully when attaching the blades to the tool. A loose installation bolt can be dangerous. Always check to see they are tightened securely. For the correct planer blade setting Your planing surface will end up rough and uneven, unless the blade is

CARBON BRUSH REPLACEMENT 0 Replace carbon brushes when they wear I_----- down to about 6mm (1/4") or sparking will occur. Both brushes should be changed at ! the same time. L 9 0 To replace carbon brushes, use the (-1 minus screwdriver equipped to remove the holder cap on the motor housing. Then replace the brush. HOW TO USE THE SHARPENING HOLDER 0 First, loosen the 2 wing nuts on the holder and insert blades Aand B as in figure at right, so that they contact side C and D. Then tighten wing nuts

5. Hold the tool firmly with both hands. 6. Keep hands away from rotating parts. 7. Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced blade. 8. Make sure the blade is not contacting the workpiece before the switch is turned on. 9. Wait until the blade attains full speed before cutting. IO. Keep at least 200 mm (8”)away from the tool at all times. 11. Always switch off and wait for the b