Log:
Assessments - 3, GPA: 4.3 ( )

Instruções de Operação MTD, Modelo 902032

Fabricante : MTD
Arquivo Tamanho: 3.38 mb
Arquivo Nome : 21547014_ENG.pdf
Língua de Ensino: en
Ir para baixar



Facilidade de uso


Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their meaning. Fig. 4 MEETS ANSI SAFETY REQUIREMENTS Our tillers conform to the safety standards of the American National Standards Institute. CHOKE CONTROL - Used when starting a cold engine. DEPTH STAKE - Controls forward speed and the depth at which the tiller will dig. ENGINE ON/OFF SWITCH - The engine switch enables and disables the ignition system. FORWARD TINE CONTROL - Engages tines in forward direction. OPERATION FUEL VALVE - The fuel valve opens and closes the passage between the fuel tank and the carburetor. RECOIL STARTER HANDLE - Used to start the engine. direction. THROTTLE CONTROL - Controls engine speed. DEPTH STAKE TINE SHIELD FORWARD TINE CONTROL TINES THROTTLE CONTROL CHOKE CONTROL ENGINE SWITCH FUEL VALVE RECOIL STARTER 7 The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask for over spectacles or standard safety glasses. TILLING The speed and depth of tilling is regulated by the position of the depth stake and wheel height. The depth stake should always be below the wheels for digging. It serves as a brake to slow the tiller’s forward motion to enable the tines to penetrate the ground. Also, the more the depth stake is lowered into the ground the deeper the tines will dig. DEPTH STAKE (See Fig. 6) Adjust depth stake by removing the hairpin clip and clevis pin. Change depth stake to desired position. Replace the clevis pin and hairpin clip. • For normal tilling, set depth stake at the second or third hole from the top. WHEELS (See Fig. 6) Adjust wheels by removing the hairpin clip and clevis pin. Change wheel position. Replace the hairpin clip and clevis pin. • For normal tilling, set wheels at the second or third hole from the top. depth_stake_4 DEPTH STAKE STAKE SPRING HAIRPIN CLIP AND CLEVIS PIN WHEEL Fig. 6 OPERATION HOW TO USE YOUR TILLER Know how to operate all controls before adding fuel and oil or attempting to start engine. STOPPING (See Fig. 5) TINES 1. Release tine control to stop move ment. ENGINE 2. Set the speed control lever at the low speed position and allow the engine to run at low speed for 1 or 2 minutes before stopping. 3. Turn the ENGINE SWITCH counterclockwise to the position “ O ” (OFF). 4. Close the fuel valve. 5. Pull the starter handle slowly and return the handle to its original position when resistance is felt. This operation is necessary to prevent outside moist air from intruding into the combustion chamber. NOTE: Never use choke to stop engine. IMPORTANT: TO STOP ENGINE IN AN EMERGENCY, TURN THE ENGINE SWITCH TO THE OFF POSITION. TINE OPERATION (See Fig. 5) • Squeeze tine control to handle. Fig. 5 TINE CONTROL “OFF” (UP) PO SI TION TINE CONTROL “ON” (DOWN) PO SI TION THROTTLE CONTROL ENGINE SWITCH FUEL VALVE RECOIL STARTER THROTTLE CONTROL ENGINE SWITCH FUEL VALVE OPERATION TO TRANSPORT CAUTION: Before lifting or trans port ing, allow tiller engine and muffler to cool. Disconnect spark plug wire. Drain gasoline from fuel tank. ARO...

Este manual também é adequado para os modelos :
Ferramentas para Jardim - 902032 (3.38 mb)
Ferramentas para Jardim - 902032 (3.38 mb)
Ferramentas para Jardim - 902032 (3.38 mb)
Ferramentas para Jardim - 902032000203200 (3.38 mb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias