Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
- with the pulley turning, force the reverse belt out of the V-groove. - slide the belt free of engine pulleys and reverse belt guides. - pull belt down and away from transmission pulley. • install new reverse belt: - thread belt up from bottom. - place belt around transmission pulley in groove. - place belt under reverse belt guides. - gently pull engine recoil rope while forcing the belt over the edge of the engine pulley into the V-groove. • install new forward belt: - place forward belt in transmission pulley groove. - gently pull the engine recoil rope to rotate the pulley while forcing the forward belt into the V-groove. 4. Replace belt guard. 5. Attach spark plug wire. Reverse Belt TRANSMISSION PULLEY Forward Belt ENGINE PULLEY Do not operate tiller before reading the engine manua l pro vided in the parts pac ket. ! CAUTION Temperature of muff ler an d near by areas may excee d 150° F. Avoi d these areas . ! WARNING IMPORTANT Engine can overheat and become damage d if debris bloc ks the coo ling syste m or rotating screen. Never run engine wit hout co mplete air cleaner insta lled on engine. OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS CRT Models ENGINE mAINTENANCE Refer to the engine manual included in your parts packet for information on engine maintenance. Your engine manual provides detailed information and a maintenance schedule for performing the following tasks: 1. check oil level before each use or after every 8 hours of operation. 2. changeoilafterfirst5-8hoursofoperation.changeoilwhileengine is warm. Refill with new oil of recommended grade. 4. check spark plug yearly or every 100 hours of operation. 5. Service air cleaner. 6. Keep engine and parts clean. 7. check engine and equipment often for loose nuts and bolts, keep these items tightened. ChECk OR FIll ENGINE CRANkCASE 1. Add oil according to engine manual. do not overfill. Use a clean, high quality detergent oil. container must be marked A.P.I. Service SF - SJ. Use no special additives with recommended oils. do not mix oil with gasoline. Oil level must be full. check the oil level by removing oil fill plug. Oil level should be up to the bottom of the fill plug opening. 2. Always check oil level before starting engine. Refer to engine manual for capacity and type of oil to use. ChECk TIllER TRANSmISSION GREASE check the grease level annually. To check the grease level: 1. Move tiller to level ground. 2. Remove grease level dipstick located between the handlebar mounts on the engine mount. correct grease level is indicated between the high and low levels on the dipstick. 3. Replace grease level dipstick in the filler hole. 4. Note that the front wheel transmission and rear tine transmission are one common reservoir.When you add to the front transmission, you must wait a short period of time for the grease to flow rearward and equalize in both front and rear.The dipstick will read correctly on level ground for both gear units. (Use Mystic 00 transmission fluid PN 1690) ChECk TIRE PRESSURE Recommended tire pressure is 20 PSI. If tires do not have equal pressure, tiller will pull to one side. ImPORTANT ENGINE IS ShIPPEd FROm FACTORYWIThOUT OIl. YOU mUST Add ENGINE OIl BEFORE STARTING ENGINE. ImPORTANT TIllERTRANSmISSION IS ShIPPEd FROm FACTORY WITh ThE PROPER AmOUNT OF lIQUId GREASE. WhEN REPlACING GREASE,ThETIllERTRANSmISSION hOldS 18- OUNCES. dO NOT OvERFIll. gear case dipstick transmission cover plate Page 16 800-345-6007 OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS CRT Models lUBRICATION Proper lubrication of moving mechanical parts is critical for proper care and maintenance.Oil the moving parts shown at 10 hour intervals using a 30 weight oil. ClEAN TINE AxlE ShAFT 1. Turn off engine. Engine must be cool. 2. Remove spark plug wire and secure from spark plug. 3. Tip the tiller forward. Block the tiller in position so that it rests on the engine mount and the tines are exposed. 4. Remove all vegetation, string, wire, and other material that may have accumulated on the axle between the inside set of tines and the seal on the transmission housing. 5. Tip the tiller back to a level position. 6. Replace spark plug wire. STORAGE PREPARE FOR STORAGE Follow the steps below to prepare your tiller for storage. Read your engine manual for detailed instructions on preparing the engine for storage. 1. Protect wheels and axles from rust: -Remove lockpin and slide wheel off hub. -coat the axles lightly with axle grease. -Slide wheel back on hub and insert lock pin. 2. Drain fuel system completely following engine manufacturer’s instructions or add fuel stabilizer to prevent fuel from gumming up during extended storage period. 3. While engine is still warm, drain the oil from the engine. Refill with fresh oil of the recommended grade. 4. clean external surfaces, engine and cooling fan. 5. Remove spark plug, pour one ounce of SAE 30 oil into spark plug hole. 6. Plug hole and pull starter cord slowly to distribute oil evenly in cylinder head area. 7. Rei...
Este manual também é adequado para os modelos :Ferramentas para Jardim - 5155 6 HP (2.42 mb)
Ferramentas para Jardim - 5055 6 HP (2.42 mb)