Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
WARNING! Non-standard accessories, cutting attachment, or replacement parts may not operate properly with your unit and may cause damage and lead to personal injury. NOTE: Using non-standard replacement parts could invalidate your Shindaiwa warranty. Daily maintenance Prior to each work day, perform the following: Y Remove all dirt and debris from the engine, check the cooling fins and air cleaner for clogging, and clean as necessary. Y Carefully remove any accumulations of dirt or debris from the muffler and fuel tank. Check cooling air intake area at base of crankcase. Remove all debris. Dirt build-up in these areas can lead to engine overheating, fire, or premature wear. WARNING! Always wear gloves when working around the cutter assembly. Y Lubricate the blades before use and after refueling. Check the cutters for damage or incorrect adjustment. Y Clean any debris or dirt from the cutting attachment. WARNING! Before performing any maintenance, repair, or cleaning work on the unit, make sure the engine and cutting attachment are completely stopped. Disconnect the spark plug wire before performing service or maintenance. ..........U This unit must never be operated with a faulty or missing spark arrester or muffler. Make sure the muffler is well secured and in good condition. A worn or damaged muffler is a fire hazard and may also cause hearing loss. Spark Plug Keep the spark plug and wire connections tight and clean. Fasteners Make sure nuts, bolts, and screws (except carburetor adjusting screws) are tight. Y Check for loose or missing screws or components. Make sure the cutter attachment is securely fastened. Y Check the entire unit for leaking fuel or grease. Blades Keep blades sharp and check blade condition frequently. If a blade’s performance changes suddenly, stop the engine and check the blade for cracks or other damage. Replace a damaged blade IMMEDIATELY! WARNING! Y Never repair a damaged blade by welding, straightening, or by modifying its shape. An altered blade may break during operation, resulting in serious personal injury. Y DO NOT use 2-tooth or NON-Shindaiwa approved 4-tooth cutting blades on Shindaiwa trimmers or brushcutters. Y Blades are not interchangeable between Shindaiwa edgers and trimmer/brushcutter models. Operating any unit with a blade or attachment not approved for that unit can be hazardous and may cause serious injury. Y Make sure nuts, bolts, and screws (except carburetor idle speed adjusting screws) are tight. ........................................................................................................................................ Cooling ...... Air intake Cooling ...... Maintenance (continued) 10-hour maintenance Perform more frequently in dusty or dirty conditions. Remove the air cleaner filter. Clean or replace as necessary. To clean filter wash it thoroughly in soap and water. Let it dry before reinstalling the filter. Air Filter Unscrew Element Fastener Remove and clean or replace the element CAUTION! Do not operate the unit if the air ..................................................................................ter is wet or water soaked. 10/15 hour maintenance Remove and clean or replace the spark plug. Y Clean the spark plug. Adjust electrode gap according to the values listed in the ”Specifications” section. If the spark plug must be replaced, use only the type recommended in ”Specifications” or equivalent resistor type spark plug of the correct heat range. CAUTION! Before removing the spark plug, cleanthe area around the plug to preventdirt and debris from getting into theengine’s internal parts. Clean the spark plug and check the gap at the electrode. 0.6–0.7 mm (0.024–0.028 inch) 50 hour maintenance Every 50 hours of operation; more frequently in dusty conditions: Y Remove and clean the cylinder cover and clean dirt and debris from the cylinder cooling fins. Gearcase lubrication Y Remove and clean the cylinder cover and clean grass and dirt from the cylinder fins. Y Remove the cutting attachment, cutting attachment holder and gearshaft collar. Remove the filler plug from the side of the gearcase and press new grease into the gearcase until old grease is pushed out. Use only lithium- base grease such as Shindaiwa Gearcase Lubricant or equivalent. Y Lubricate mainshaft splines. Old grease Gear shaft collar New grease Lubricate gearcase Maintenance (continued) ntenance (continued) 50 hour maintenance Remove and replace the fuel filter element. Before reinstalling the new filter element, inspect the condition of all the fuel system components (fuel pick-up line, fuel return line, tank vent line, tank vent, fuel cap and fuel tank). If damage, splitting or deterioration is noted, the unit should be removed from serr rr vice until it can be inspected or repaired by a Shindaiwa-trained service technician. CAUTION! Make sure you do not pierce the fuel line with the end of the hooked wire. The line is delicate and can be dam aged easily. .................
Este manual também é adequado para os modelos :Ferramentas para Jardim - 89302 (1.44 mb)
Ferramentas para Jardim - 89302 (1.44 mb)
Ferramentas para Jardim - 89302 (1.44 mb)
Ferramentas para Jardim - 89302 (1.44 mb)