Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
Call Factory before 63 1166-1 Shim-wheel shaft, 1 -1/64" inner diam.. ordering)................................... 1 .062" thick................................. As Req’d 79 9359 Pin-alignment............................... 1 63 1166-2 Shim-as above, .030“ thick ...... As MISCELLANEOUS PARTS Req’d 80 9560 Bolt-hex hd., 1/2-13 x 2" Grade 5. 2 63 1166-3 Shim-as above, .015“ thick As Req’d 81 9928 Washer-disc spring (concave), domed side faces bolt head....... 2 63 1166-4 Shim-as above, .010“ thick As Req’d 82 2126 Post-with threaded hole for Ref. No. 80........................................ 2 63 1166-5 Shim-same as above, .005“ thick As 83 9726 Plug—pipe, 1/4".............................. 2 Req’d 84 9122 Plug-red plastic, thread protector. 1 64 1086 Bushing-bronze, wheel shaft bearing ..................................... 2 85 9205 Clip-forward interlock system plug connector (see page 17)............ 1 65 1878 Shaft-wheel, 15-5/8", (Incl. two of Ref. No. 62 and one Ref. No. 66) 1 86 1900759 Decal-forward interlock wire harness...................................... 1 66 9357 Key-Hi Pro, 1/4" x 1-3/4".............. 1 67 1223 Gear-slow speed, wheel drive...... 1 68 1232 Gear-fast speed, wheel drive....... 1 69 1237 Dog Clutch-wheel drive............... 1 70 1112 Pin-clutch guide, 1/4“ diameter... 3 11 TROY-BILT HORSE TILLER MODELS 12068, 12069, 12070 AND 12071 TILLER ATTACHMENT TRANSMISSION ASSEMBLIES 18 (Figure 6) MODELS 12068, 12069, 12070 AND 12071 TROY-BILT® HORSE TILLER REF No. PART No. DESCRIPTION QTY. REF No. PART No. DESCRIPTION QTY. 1 1908211 Bolt-hex hd., 1/4-20 x 5/8", self- 17 1224-2 Shim-same as above, .030" As locking flange........................... 5 thick......................................... .Req'd 2 20873 Cover—tiller housing (incl. five of 17 1224-3 Shim-same as above, .005“ As Ref. No.1)................................. 1 thick......................................... .Req'd 3 1129-1 Gasket—tiller housing cover, .010" As 17 1224-4 Shim-same as above, .062“ As thick.......................................... Req’d thick......................................... .Req'd 3 1129-2 Gasket-same as above, .030“ As 18 1714 Bearing & Cup-sold as set only.. . 2 thick.......................................... .Req'd 19 11602 Shaft-main tiller drive (incl. an 4 1901972 Shaft—tiller tine............................. 1 integral worm gear, plus two 5 97074 Ball Bearing.................................. 2 pressed-on cone roller bearings, 6 1901976 Worm Gear-bronze, tiller tine two bearing cups (Ref. No. 18) and shaft......................................... 1 one shoulder washer............... . 1 7 1104 Key—tiller tine shaft, woodruff key 1 20 9617 Seai-oil, drive shaft, front........... . 1 8 97073 Seal—oil, tiller tine shaft................ 2 21 9517 Retaining Ring-internal............... . 1 22 1138-1 Washer-shoulder (drive shaft).... . 1 TILLER DRIVE SHAFT ASSEMBLY 9 9500 Retaining Ring-external............... 2 TRANSMISSION HOUSING AND DIPSTICK 10 1909138 Dog Clutch—tiller drive shaft......... 1 23 1902000 Housing—tiller attachment (incl. 11 9301 Key-3/16“ x 1".............................. 1 pressed-on sleeve in front of 12 2127 Spring-dog clutch........................ 1 housing). Empty housing 13 1138-1 Shlm-dog clutch, 1/16"(.62”) thick. 1 without shafts, gears, seals, 14 1908212 Bolt-hex hd., 1/4-20 x 7/8", self- dipstick, etc. Call Factory locking flange........................... 3 before ordering........................ 1 15 1900881010 Cap-rear bearing.......................... 1 24 1909157 Dipstick-oil level, tiller attachment 1 16 1124-2 Gasket-rear bearing cap.............. 1 17 1224-1 Shim-front bearing cap, .010“ As thick.......................................... Req'd 13 TROY-BILT HORSE TILLER MODELS 12068, 12069, 12070 AND 12071 BOLO TINE ASSEMBLIES (Figure 7) (As viewed with blunt edge facing you.) MODELS 12068, 12069, 12070 AND 12071 TROY-BILT® HORSE TILLER REF No. PART No. DESCRIPTION 0TY. STANDARD TILLING TINES 1 1901975010 Tine Holder-welded steel, fits left or right sides...................... 2 2 9761 Bolt-hex hd„ 3/8-16x2"............. 4 3 9807 Locknut—3/8"-16.......................... 4 4 —- This Ref. No. not used................. 5 —- This Ref. l\lo. not used................. 6 1270-1A Bolo Tine-single, left hand. Used on left and right side tine assy. Tine is stamped either “EL" or “AL". (Incl. two each of Ref. No.’s 8, 9 and 10)............................. 8 7 1270-2A Bolo Tine-single, right hand. Used on left and right side tine assy. Tine is stamped either “ER" or “AR”. (Incl. same hardware as Ref. No. 6)............................... 8 8 9711 Bolt-hex hd„ 3/8-16x1”............. 16 9 9913 Lockwasher-3/8"......................... 16 10 9802 Nut-hex, 3/8"-16........................
Este manual também é adequado para os modelos :Ferramentas para Jardim - 12068 (2.38 mb)