Assessments - 3, GPA: 4.7 ( )

Fabricante : Echo Arquivo Tamanho: 1.01 mb Arquivo Nome : Língua de Ensino:

Secure with two (2) 6mm x 30mm bolts. 9. Install hook. Three loop hook included with Blade Conversion Kit for blade use. Position 8 5/8 inch (220mm) from engine end of drive shaft assembly. DO NOT tighten at this time. 10. Install handles in bracket (G), place clamp top over handles and securewithfour(4)5mmx35mmbolts(H). 400 mm (15*3/4 In.) 220 mm (8-21/32 In.) ENGINE END 1SMEEHO. 11. Secure throttle cable and leads to drive shaft by sliding wedge under harness hook. 12. Install power headand align gear box, power head and U-handles. Tighten all screws. 13. Place throttle cable in slot in bracket. One nut and washer on each side of bracket. Finger tighten both nuts (A). 14. Attach inner cable to swivel (B). Check throttle for freedom of movement and that wide open throttle / low idle extremes are adjusted properly. If adjustment cannot be achieved with adjusting nuts, the outer cable must be adjusted by moving the Cable Adjustment Clamp (I). Consult with your Echo Dealer for correct adjustment procedure. IS. Attach ignition leads (C). Grass Trimmer/Brush Cutter a q Operator's Manual * ^ Pre - Operation OPERATION WITH BLADES Preparing the Trimmer/Brush Cutter for Blade Use WARNING A DANGER Blade use DEMANDS specific Brush Cutter configuration. Operation without specified shield and harness can result in serious personal injury. Plasticand Nylon Blades Require "Blade Conversion Kit," P/N99922200410 (metal shield and shoulder harness). - Steel/Metal Blades Require "Blade Conversion Kit" PLUS a "U-Handle Kit" P/N 35130449230 or Combination Blade andU-HandleKitP/N 99944200450 _ Choosing the Correct Blade WARNING A DANGER The type of Blade used MUST be matched to the type and size of material cut An improper or dull blade can cause serious personal injury. Blades MUST be sharp. Dull blades increase the chance of kick out and injury to yourself and bystanders. Plastic/Nylon Blades may be used where ever the nylon line head is used. DO NOT use this blade for heavy weeds or brush! 201/UECHO. 8 T ooth Weed/Grass Blade P/N 696001203 31 is designed for grass, garden debris and thick weeds. DO NOT use this blade for brush or heavy woody growth, 3/4" in. (19 mm) diameter or larger. Brush/Clearing Blade P/N 69500120331 is designed for cutting brush and woody growth up to 3" in. (76 mm) diameter. Use Shoulder/Waist Harness P/N 99944200200 Use of the Shoulder/ Waist Harness is recommended for ALL Trimmer/Brash Cutter use, not just Blade operation. The Shoulder/Waist Harness when used in a trimming operation with nylon line head suspends the trimmer from the operator's shoulder and reduces operator fatigue. During blade operation, the same fatigue reduction is achieved. Safety to the operator is also enhanced by preventing blade contact with the operators hands and feet by restricting trimmer movement. NOTE In case of Emergency, pull up on the Quick Release Collar to disconnect the trimmer from the harness. Grass Trimmer/Brush Cutter Operator’s Manual £ I FUEL Fuel Requirements — Gasoline - Use G9 Octane [ gasoline known to be good quality. Gasoline may contain up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol) is NOT approved. Two Stroke Oil - A two-stroke engine oil meeting proposed ISO-L-EGD Standard (ISO/CD 13738), must be used. Echo brand Ptemium50:1 oil meets this proposed standard. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD approved oil, such as Echo Premium 50:1 Two-stroke Oil, will void the two-stroke engine warranty. (Emission related parts only are covered for two years, regardless of two-stroke oil used, per the statement listed in the EPA Phase 1/Califomia Emission Defect Warranty Explanation.) Mixing - Follow directions on the oil container. Handling Fuel — WARNING A DANGER Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result. - Use an approved fuel container. - DONOTsmokenearfiiel. - DO NOT allow flames or sparks near fuel. - Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize. - NEVER refuel a unit when the engine is HOT! - NEVER re fuel a unit with the engine running. - DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks out doors over bare ground. - Securely tighten fuel cap after refueling. - Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired. After Refueling- - Wipe any spilled fuel from the unit. - Move at least 3M. (10 ft.) from refueling location before starting. After use- - DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage container. Storage - Fuel storage law s vary by locality. Contact your local government for the laws affecting your area. As a precaution, store fuel in an approved, air tight container. Store in ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :