Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
Before starling to assemble the tiller, be certain to remove all of the parts irom the carton. Assembly For ease lnassembllng the tiller, follow the sequence of steps outlined below; 1. Removo all masking tape irom the ends of the tine shaft and the drive pulley shaft oi the chain guard assembly. 2. To attach the deflector assembly to the chain guard assembly; remove 2 mounting bolts from each aide of ihe chain guard as shown In Figures I & 2. Mount the deflector зо that the holes In the mounting brack“ ets line up with the holes in the chain guard assembly as shown in Figure 3, and replace the mounting bolts In thoir original holes. Tighten the bolts securely* Tiller Drive Shaft Defloctor Mounting fcol Grease Tilting Tine Shaft 32" Heavy Duty Tiller Mfr's No. 174 Fig. 3 3. Assemble the left hand Inner tine assembly to the left hand outer tine assembly and fasten with a pin and cotter pin. Assemble the right hand inner tine assemble to the right hand outer tine assembly, and faston with a pin and cotter pin. NOTE: the inner tine assemblies can be Identified by the constant diameter of the hub fastened to the tLne pLate, The long end of this hub Is inserted into the long end of the hub of the outer tine assemblies and Is fastened as described above. CAUTION: As itis possible to mount the tine assemblies Incorrectly to the tine shaft, pay particular attention to the following: Assemble the tines to the tine shaft as shown in Figure 4 so that the sharp odgas of the top tines face toward the front of the tractor. Fasten the tines to the tine shaft with a pin and cotter pin on each end of the tine shaft. When the tines are mounted, check one© more to be certain that the sharp edges of all tines face In the correct direction. 4. Assemble the tiller drive pulley to the tiller drive shaft as shown in Figure 3. The pulley Is held in place by a key and Set screw and Is to be mounted with tho hub of the pulley facing away from the chain guard. Left Hand Outer Tine A^tieinoly Left Hand Inner «Tine Assembly Right Hand Inner Tine Assembly Right Hand Outer Tine Assembly Fig. 2 SIMPLICITY MANUFACTURING LI1H0 IN lliA Fig. 4 COMPANY / PORT WASHINGTON. WIS. Tiller Drive Assembly For ease In attaching the tiller drive assembly to the tractor, follow the sequence of steps outlined below: 1. Fasten the belt release bracket to the outside of the side plate with the two 5/16" x 1" hex capscrews as shown In Fiyure 5. 2 . Mount the tiller belt release guard to the belt release bracket as shewn in Figure 5, The concave surface of the tiller belt release guard is to faco the bevel gear shaft, 3. Mount the %" tiller drive pulley to the bevel gear shaft with Its key, as shown In Figure 5 . The hub of the pulley faces in toward the tractor, Leave the set screw loose until making ifnal-dllgtimeiu, Fig. 5 4. Place the 5&*' long V-bolt #105122 in position on the 3*' tiller drive pulley, ( For ease of identification, the V-belts are marked with part numbers . ) 5« Place the 42" long V-belt £154273 Ln position on the smaller pulley of the tiller drive assembLy and mount the tiller drive assembly onto the lift shaft as shown in Figure 6, As is shown ln Figure 7, the arm of pulley sleeve assembly is held ln place against the left side bracket of the tractor tow a5sembly by means of a hair pin cotter end pin. Place the free end of the 56" long V-bell £105122 ln position on the large pulley of the tiller drive assembly as shown in Figure 6, Position the 3". pulley so that it is in line with the large pulley of the tiller drive assembly and tighten the set screw securely. 6. Place the off-set end of the guLde assembly rod into the hole in the belt release bracket and fasten Ln place with a hair pin cotter.. See Figure 6. Fig. 6 2 Attachment Lubrication For ws« in attaching the tiller lo the tractor, follow l!i t? i.oquencc oi steps as outlined below; ]. Пасе the иНнг in position In back, of the tractor. Pul) tin tractor lift lever to the lull back position and 1>1;>сн the tiller lift Ьбг assembly into the tube of the rear lltt assembly on the tractor, fasten in place with a pin and hair pin cotter as shown In Figure 8. 2. Place the tractor lift iever In the forward position and connect the tiller frame to the tractor tow assembly wi Lb lh« pivot rod and hair pin cotters. See Fig. 8. j. Turn the belt tension adjusting screw to the full loose position ( turn counter-clockwise ) ^nd piece the free end of the 42” long V-belt fUS427.1 in position on the tiller drive pulley. With the V-belt in position on Lhe til)«r drive pulley and on the smaller pulley of the tljier drive assembly, turn the btll tension adjusting screw in a clockwise direction until the s^iack lc taken out oi the V-belt. 4. Pull up on the tiller ekutch lever handle to engage the tiller, iind ridjust the belt release guard so that clearance is equal on both sides of the belt. See Figure &. 5. Depress the factor brake pedal and lock In positio...