When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! ! © Copyright 2012 Printed 20583 313-306M PSN2096 Primary Seeder Operator’s Manual 5/15/12 Table of Contents Important Safety Information . . . . . . . . . . . . . 1 Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . .1 Look For The Safety Alert Symbol . . . . . . . . . . . . .1 Safety Labels . . . . . . . . . . . . . . . . .

See “Flow Control Valve Plumbing” on page 21 for plumbing requirements. Solenoid Control Option: The Tractor’s hydraulic control lever and PTO shaft will need to be engaged to make control stick functional checks. Independent Control Option: Only the Tractor’s PTO shaft will need to be engaged to make control stick functional checks. 10/11/12 RCP2660, RCPM2660, RCP3060 and RCPM3060 Parallel Arm Rotary Cutter 316-111M 25 26 Section 2: Hydraulic Set-up Options RCP2660, RCPM2660, RCP3060 and RCPM30

The driveline must be lubricated before putting it into service. Refer to “Lubrication Points” on page 50. The tractor’s PTO shaft and cutter gearbox shaft must be aligned and level with each other when hooking-up the driveline to the tractor. Refer to Figure 1-5: 1. Start tractor and slowly engage 3-Point controls to move lower arms until the PTO shaft for the speed increaser is aligned and level with tractor PTO shaft. Securely block cutter in this position. 2. Place tractor gear selector in p

When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! ! © Copyright 2012 Printed RCP2660, RCPM2660, RCP3060 and RCPM3060 Parallel Arm Rotary Cutter 30028 316-111M Operator’s Manual 10/11/12 Table of Contents Important Safety Information . . . . . . . . . . . . . 1 Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . .1 Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . .

Locate shield forward/back and up/ down to provide the best overall coverage for the tractor operator. Use a spirit level to level the shield before marking. Mark frame location with a pencil on each side of the ROPS bar; and mark vertical ROPS location on the shield frame. 4. Position protective shield (#5) on a flat work surface. Locate one of the flatbars (#4) next to the pencil marks to determine which set of holes will clear the vertical marks for the ROPS location. Mark hole location and d

Seed cup damage may occur. 22 OS1548 and OS1572 Overseeder (S/N 166724+) 308-303M 5/21/12 Table of Contents Section 3: Adjustments Cup Setting 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 Lovegrass - Sand (Pounds per Acre) High Range 0 89 140 191 242 293 343 394 445 496 547 598 649 700 751 802 852 925 977 1029 1081 Low Range 0 28 44 61 77 93 109 125 141 157 173 189 206 222 238 254 270 286 302 319 335 Lovegrass - Sand (Pounds per 1000 Square Feet) High Range 0.0 2 3.2 4.4 5.6 6.7

When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! ! © Copyright 2012 Printed OS1548 and OS1572 Overseeder (S/N 166724+) 308-303M 26780 Operator’s Manual 5/21/12 Table of Contents Important Safety Information . . . . . . . . . . .1 Seed Rate Charts (Metric) . . . . . . . . . . . . . . . . . .24 Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . .1 Look For The Safety Alert Sym

. Section 4 Page 25 Proper tension and alignment on all drive chains. Operator’s Manual Safety decals are correctly located and legible. Replace if damaged. Important Safety Information Sling Bracket Refer to Figure 1-1 The sling brackets allow points at each end to hook the chain for lifting of the unit. When hooking the chain to the sling brackets, be certain to either use a spreader bar on the chain or use a long chain to prevent bending the sling brackets. Sling Bracket Figure 1-1 Tire Track

Objects can be thrown forward toward the operator causing serious bodily injury or death. ! DANGER Do not point outlet toward people, animals, or buildings and keep people and animals away from outlet during operation. Tine impact on objects can cause projectiles resulting in bodily injury or death. ! DANGER Do not till across steep inclines exceeding 15 degrees. The action of the tines being forced down into the ground can cause the tractor to roll-over resulting in serious injury or death. Con

4. Inspect clutch to ensure scribed markings made on the clutch plates have changed position. Slippage has not occurred if any two marks on the friction disk and plate are still aligned. A clutch that has not slipped must be disassembled to separate the friction disk plates. See “Clutch Disassembly” to disassemble clutch. 5. Tighten each of the 8 spring retainer nuts on the clutch housing exactly 2 revolutions to restore the clutch to the original setting pressure. 6. The clutch should be checke