Replace any missing or illegible safety decals. Inspect for any damaged or worn parts and replace before next use. Store the Rough Cut Mower in a dry environment. 16 MAINTENANCE 1. Periodically check and maintain proper gear oil level. 2. Approximately every 8 hours, grease spindles (3), roller axle (1), wheel forks (4), wheel axles (4), PTO shaft universal joints (2), and PTO telescoping surface. NOTE: Use a high-temp/multi-purpose grease. 3. Before each use check to make sure all safety

Do not allow anyone to operate or assemble this equipment until they have read this manual and have developed a thorough understanding of the safety precautions and operation. Review safety instructions with all users annually. • This equipment is dangerous to children and anyone unfamiliar with its operation. The operator should be a responsible, properly qualified and physically able person familiar with farm machinery and competent in this equipment’s operation. • Never exceed the limits o

Mower not level side to side, uncut or partially cut grass. 2. Blades dull or bent. 3.Carrier RPM too low. 4. Field conditions are so wet that the tractor tire is pushing grass into mud. 5. Ground speed too fast. 6. Blades lock back. 7. Blades riding up due to blade bolt wear or loose bolts. 8. Grass is down from previous weather conditions, 9. Possible build up of marerial under mower. Level 3 pt. Hitch linkage on tractor. Sharpen or replace blades. Use correct PTO speed. Too wet to

Always mix all fuels in a clean approved container. 1. Place the unit on a flat, level surface, and wipe any debris from around the fuel cap. 2. Remove the fuel cap. 3. Fill the tank with clean, fresh fuel. 4. Replace the cap, and wipe away any spilled fuel before starting the engine. 11 Starting the Engine 4. While holding the outer tube firmly Engine ignition is controlled by a two with one hand, slowly pull the recoil position switch mounted on the throttle starter handle until resis

FR_1 SHINDAIWA OWNER’S/OPERATOR’S MANUAL P231 POLE PRUNER Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself with the contents. Always wear eye and hearing protection when operating this unit.WARNING! Part Number 62891-94311 Rev. 3/08 Introduction Attention Statements The Shindaiwa P231 Pole Pruner is designed and built to deliver superior performance and reliability without compromise to quality, comfort, safety or durability. Shindaiwa’s high- perform

Box 2810 Tualatin, Oregon 97062 Telephone: 503 692-3070 FAX: 503 692-6696 Shindaiwa Kogyo Co., Ltd. Head Office: 6-2-11 Ozuka Nishi, Asaminami-ku Hiroshima, 731-3167, Japan Telephone: 81-82-849-2220 FAX: 81-82-849-2481 2002 Shindaiwa, Inc. Part Number 63888-94010 Printed in Japan Rev. 2/02 Specifications subject to change without notice. SHINDAIWA OWNER’S/ OPERATOR'S MANUAL P231 POLE PRUNER WARNING! Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself wit

ECHO provides an Operator's Manual and a Safety Manual with your original Power Pruner™ Those manuals and this manual must be read and understood for proper and safe operation. X7502300600 89865022060 04/07 2 HUECHO 5 FOOT EXTENSION INSTALLATION Tools Required: Screwdriver, 3 mm Hex Wrench, Measuring Tape Parts Required: 1524mm (5 Foot) Extension WARNING DANGER The Saw Chain is sharp! Always wear gloves when handling the cutting attachment, otherwise serious personal injury may result.

SRM-260SB S/N 05001001 - 05999999 Engine, Short Block, Ignition, Cylinder Cover..............................................................................................................4 Starter, Fuel System........................................................................................................................................................6 Clutch, Fancase........................................................................................................................

..........................................20 Plastic Shield.................................................................................................................................................................22 Part Number Index.........................................................................................................................................................24 Part Description Index..................................................................................

13 90080000609 1 BEARING, BALL - 609 14 90070600010 1 CIRCLIP 10 15 61023904130 2 WASHER, SHIM 16 61046027431 1 HOUSING, GEAR 17 90024205010 1 SCREW 5X10 18 61043450031 1 BOLT 8X8 19 90010005035 2 BOLT 5X35 20 90060000005 2 WASHER 5 99922203538_260SB/05 - 21 -REVISED 09/28/06 Table of Contents Part Number Index TRIMMER/ BRUSHCUTTER Plastic Shield 99922203538_260SB/05 - 22 -REVISED 09/28/06 Table of Contents Part Number Index TRIMMER/ BRUSHCUTTER Plastic Shield REMARKSDESCRIPTIONQTYPART NUMBER IT