2 - 5 x 8 mm screws, 2 - 5 mm nuts, 2 - 5 mm lock- washers, (bracket to shield). 2 - 5 mm nuts, 2 - 5 mm lockwashers (Bracket to Gear Housing) Assembly (continued) 1. If installed remove nylon line head, adapter plate, shield plate, and plastic shield: a. Align locking hole in adapter plate with notch in edge of gear housing and insert head locking tool (A). b. Remove line head (B) by turning it clockwise until head is completely off of shaft. c. Remove locking tool. d. Removethreescrewsholdings
Emission Control (Exhaust & Evaporative) EPA 2010 and Later and/or C.A.R.B. TIER III The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for the fuel tank the Control System is EVAP (Evaporative Emissions) or N (for nylon tank). Evaporative emission may be applicable to California models only. An Emission Control Label is located on the unit. (This is an EXAMPLE ONLY; information on label varies by engine FAMILY). PRODUCT EMISSION DURABILITY (EMISSIO
NOTE: For proper operation, always refer to the instructions accompanying the trimmer head being used. Trimmer head styles: Semi-automatic. Trimmer line is indexed when the operator taps the trimmer head on the ground during operation. Manual. The operator indexes line manually with the grass trimmer stopped. Fixed. The operator must stop the unit and add new lengths of trim- mer line manually. Flail. This device, designed for clearing weeds and light brush, fea- tures three nylon blades attache
Remedy Use a lower throttle setting. Consult with an authorized Shindaiwa servicing dealer. Refill with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO FD classified oils at 50:1 gasoline/oil ratio. Clean, repair or replace as necessary. Consult with an authorized Shindaiwa servicing dealer. Service the air cleaner element. Tighten or replace the spark plug. Check the Specifications section for the
• Operation of the unit with improperly maintained/removed cutting shield or removed/damaged air filter. • Damage caused by dirt, pressure or steam cleaning the unit, salt water, corrosion, rust, varnish, abrasives, and moisture. • Defects, malfunctions or failures resulting from abuse, misuse, neglect, modifications, alterations, normal wear, improper servicing, or use of unauthorized attachments. • Incorrect storage procedures, stale fuel, including failure to provide or perform required maint
8.8 shearbolt Slip Clutch/Optional 10 x 55 mm Metric Gr. 8.8 shearbolt Slip Clutch/Optional Slip Clutch Standard Blade Holder(s) Straight Oval type Oval type Oval type Oval type Blades 3/8 x 3 inch uplift 3/8 x 3 inch uplift 1/2 x 4 inch uplift 1/2 x 4 inch uplift 1/2 x 4 inch uplift Blade Tip Speed 11,400 FPM 13,029 FPM 14,335 FPM 14,963 FPM 14,963 FPM Tires Laminated or Solid Rubber Laminated or Solid Rubber Laminated or Solid Rubber Laminated or Solid Rubber Laminated Tractor HP Range 1
ift 1/2 x 4 inch uplift 1/2 x 4 inch uplift 1/2 x 4 inch uplift Blade Tip Speed 11,400 FPM 13,029 FPM 14,335 FPM 14,963 FPM 14,963 FPM Tires Laminated or Solid Rubber Laminated or Solid Rubber Laminated or Solid Rubber Laminated or Solid Rubber Laminated Tractor HP Range 10 - 25 PTO 15 - 30 PTO 25 - 40 PTO 30 - 45 PTO 50 - 70 PTO Front and Rear Deflectors Standard (Front Belting/Rear Band), All 5 Models Approximate Weight 397 lbs 455 lbs 636 lbs 764 lbs 1024 lbs Warranty 1 year limite
Bush Hog® TOUGH SQUEALER* Series Rotary Cutters BUSH HOG® TOUGH FEATURES TOUGH EZ Clean Sloped Decks TOUGH Sidebands With Welded Skids TOUGH EZ Lube Drivelines TOUGH Bush Hog® Gearboxes TOUGH Quick Detach Gearbox Shields TOUGH Full Length Replaceable Skids TOUGH Powder Coat Paint Model SQ160 MODELS^^^H SQ142 SQ148 SQ160 SQ172 SQ184 Cutting Width 3 ft 6 inches 4 ft 5 ft 6 ft 7 ft Cutting Capacity 1 inch dia. 1 inch dia. 2 inch dia. 2 inch dia. 2 inch dia. Cutting Height 2 to 12 inches 2 to
II & III Quick Hitch Deck Thickness 10 gauge Tractor PTO Speed 540/1000 RPM Blade Holder Round Type Blades 1/2 x 3 inches, Double Edge Blade Tip Speed 17,300 FPM at 540 RPM Blade RPM 1100 Blade Rotation Clockwise, but Reversible Cutter Head Movement 90° Up to 85° Down Driveline ASAE Category 4, 540 or 1000 RPM Hydraulic Pump Mounting Machine Only, PTO Driven Hydraulic Oil Capacity 35 Gallons, Factory Filled Hydraulic Capacity 24 GPM Overload Protection Hydraulic Relief Valve Counte