The obligation of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defective parts. Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety (90) days from the date of purchase of such part or to the expiration of the applicable new equip- ment warranty period, whichever occurs later. Warranted parts shall be provided at no cost to the user at an authorized Bush Hog dealer during regular working hours

4. Input Gearbox -Add EP80W-90 gear oil, if necessary, to bring oil level to check plug. 5. Lateral Gearbox -RTH Models (Gear Drive) -Add EP80W-90 gear oil, if necessary, to bring oil level to check plug located on side of gearbox. 6. Chain Drive -RTN,RTNR Models -Add EP80W-90 gearoil, if necessary, to bring oil level to check plug located on side of cover. 40 HOURS 7. Rotor Shaft Bearing -Apply 2-3 shots of multi- purpose grease with hand pump grease gun every 40 hrs. of operation and before st

Traveling at the slowest forward speed with rear shield fully lowered will give finest possible finish. This shield adjustment is good for mulching, mixing, and burying weeds, fertilizer, etc. The more you increase forward speed and shield height, the coars- er the finished results will be. To leave the ground surface rough with larger clods and residue exposed, work with shield fully raised. When working in rocky soil, always have shield in raised position. Figure 3-1 Adjustments Adjustable, Sp

ALWAYS stop the engine immediately and check for damage if you strike a foreign object or if the unit becomes tangled. Do not operate with broken or damaged equipment. NEVER allow the engine to run at high RPM without a load. Doing so could damage the engine. NEVER operate a unit with worn or damaged fasteners or attachment holders. Shoulder Strap C2510 IMPORTANT! Adjust the shoulder strap so the shoulder pad rests comfortably on the off-side shoulder and the cutting path of the cutting attachme

Shorted ignition ground. Faulty ignition unit. Move switch to “I” (ON) position and restart. Consult with an authorized servicing dealer. NOYESYESCheck the spark plug. If the plug is wet, excess fuel may be inthe cylinder. The plug is fouled or improperly gapped. The plug is damaged internally or of thewrong size. Crank the engine with the plug removed, reinstall the plug and restart. Clean and regap the plug to 0.024 - 0.028inch (0.6 - 0.7 mm). Restart. Replace the plug with an NGK BPMR6A orequ

............................................................................... ........................................................................... ................................................................... ....................................................................... ............................... ........................................................................... ..................... ..........................................................................

(when trimmer head is in use) 1. Attach the shield extension to the cutting attachment shield. See figure 9B. WARNING! NEVER use this machine without sub-shield when using a trimmer head. Sub-shield Hook Hook Receiver Cutting Attachment Shield Figure 9B CAUTION! Make sure the sub-guard is completely hooked at the hook receiver. Assembly (Continued) Handle Bar C3410 Install the handlebar: 1. Use the 4 mm hex wrench to remove the lower cap retaining screws from the handlebar bracket. Remove the ca

8.8 2 13 9100204 SPRING WASHER 8MM 2 BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL OCTOBER, 2012 MAINARM REF. PART NO. NO. DESCRIPTION QTY. 1 41199.06 MAINARM W/ASSY RH 1 2 21149.01 PIVOT, BUSHING 2 3 0901121 GREASE NIPPLE, 1/8" BSP-STRAIGHT 3 4 41200.02 TENSION LINK 1 5 7105050 BUSHING, ROD END 1-1/4” OD X 1“ ID 2 6 41268.02 MAIN PIVOT PIN 1 7 9313045 CAPSCREW M10-P1.5 - 20MM 1 8 00765676 LOCKNUT, M10-P1.5 TOP LOCK 1 9 41691.04 PIN W / ASSY. - LIFT / REACH-MAG420 1 10 9313065 CAPSCREW 10-P1.5

n Always make sure the cutting attachment shield is properly installed before operating this unit. Operating Units with a Blade The blade rotates counter-clockwise. For best performance and to minimize being stuck by debris, move the blade from right to left while advancing on your work. Position the blade so cuts are made between the blade’s 8 o’clock and 10 o’clock positions (as viewed from above). DO NOT cut between the 10 o’clock and 5 o’clock positions. WARNING! When cutting wood with a saw

Oil is a registered JASO FC classified oil and also meets or exceeds ISO-L-EGD performance requirements. Shindaiwa One is recommended for use in all Shindaiwa low emissions engines and also includes a fuel stabilizer. Filling the Fuel Tank 1. Place the trimmer on a flat, level surface. 2. Clear any dirt or other debris from around the fuel filler cap. 3. Remove the fuel cap, and fill the tank with clean, fresh fuel. 4. Reinstall the fuel filler cap and tighten firmly. WARNING! Minimize the risk