Assessments - 4, GPA: 4.5 ( )

Fabricante : Axor Arquivo Tamanho: 701.84 kb Arquivo Nome : Install_4247.pdf Língua de Ensino:

Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B. POP-UP DRAIN Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 6 2 4 3 2 TIGHTEN LOCKNUT 1 REMOVE FLANGE Remove CLEAR PLASTIC COVER (1). Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 2 2 3 3 1 1 Tighten LOCKNUT (1) firmly with Adjustable Wrench or Channel Locks. INSTALL DRAIN FROM BELOW FIXTURE 5 From under side of SINK install DRAIN BODY (1) up through drain outlet. Note: No plumber’s putty or caulk is required. The CABLE ATTACHMENT POINT (2) must face towards the rear of the SINK. Install FOAM GASKET (3) and FLANGE (4) onto drain body from above SINK and tighten FLANGE (4) firmly. 4 Fig. A. Fig. B. Fig. A. Fig. B. POP-UP KNOB (1) must be fully down. Fig. B. FLANGE GASKET AND POP-UP KNOB Check DRAIN FLANGE in SINK to ensure that WHITE FOAM GASKET (3) is fully compressed and not visible. Fig. A. DRAIN BODY 4 2 DRAIN OUTLET 1 3 4 REAR OF SINK M965016 REV.1.7 8 CHECK OPERATION OF POP-UP 9 MAKE WATER SUPPLY AND WASTE CONNECTIONS Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. Fig. A. 7 ATTACH CABLE CONNECTOR 2 1 Fig. B. 1-1/4” O.D. 3 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. 1 APPROX. 20" 2 HOT COLD 3/8" COMPRESSION RED BAND BLUE BAND Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connect left SUPPLY (1) to Hot (Marked with a Red Band) and right supply to COLD (2) wall supply. Faucet supplies are 20" long from faucet base. Note: If additional supply length is required, installer must purchase additional parts separately. Important: If SUPPLY HOSES (1, 2) are to long, loop as illustrated to avoid kinking. Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet. 2 1 M965016 REV.1.7 12 11 4 2 8 2.5mm HEX KEY 5 6 3 4 7 REMOVE INSTALL SERVICE To remove or replace cartidge: Fig. A. Turn valve to OFF position. Remove HANDLE SCREW (2). Pull off HANDLE (3) and CAP (4). Unthread CARTRIDGE NUT (5) and remove. Pull out CARTEIDGE (6). Inspect CARTRIDGE (6) and O-RING (7) for debris and clean if necessary. Clean MANIFOLD (8) and rinse clean. Reinstall CARTRIDGE (6) and O-RING (7) onto MANIFLOD (8). Reinstall CARTRIDGE NUT (5), CAP (4) and HANDLE ASSEMBLY (3). If spout drips, operate handle several times from OFF to ON and HOT to COLD position. Do not force - handles turn only 90°. Turn off hot and cold water CAUTION supplies before beginning. 2 TEST INSTALLED FITTING With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3). Operate HANDLE (1) to flush water lines thoroughly. Replace AERAT...

Baixe o seu

Para fazer o download, introduza 2 dígitos :