Assessments - 5, GPA: 3.8 ( )

Fabricante : American Standard Arquivo Tamanho: 701.84 kb Arquivo Nome : Install_4247.pdf Língua de Ensino:

Important: If SUPPLY HOSES (1, 2) are to long, loop as illustrated to avoid kinking. Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet. 2 1 M965016 REV.1.7 12 11 4 2 8 2.5mm HEX KEY 5 6 3 4 7 REMOVE INSTALL SERVICE To remove or replace cartidge: Fig. A. Turn valve to OFF position. Remove HANDLE SCREW (2). Pull off HANDLE (3) and CAP (4). Unthread CARTRIDGE NUT (5) and remove. Pull out CARTEIDGE (6). Inspect CARTRIDGE (6) and O-RING (7) for debris and clean if necessary. Clean MANIFOLD (8) and rinse clean. Reinstall CARTRIDGE (6) and O-RING (7) onto MANIFLOD (8). Reinstall CARTRIDGE NUT (5), CAP (4) and HANDLE ASSEMBLY (3). If spout drips, operate handle several times from OFF to ON and HOT to COLD position. Do not force - handles turn only 90°. Turn off hot and cold water CAUTION supplies before beginning. 2 TEST INSTALLED FITTING With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3). Operate HANDLE (1) to flush water lines thoroughly. Replace AERATOR (3). 5 4 2 CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in SINK. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting section in these instructions. Release POP-UP KNOB (4) down and check all drain connections and "P" trap for leaks. Tighten if necessary. 10 “P” TRAP WASTE OUTLET 3 1 OFF ON COLD HOT To change from swivel to fixed spout, proceed as follows: Remove SET SCREW (1) using Hex Wrench supplied. VIEW “A” Install FIXING SET SCREW (2) using Hex Wrench supplied. Align SPOUT (3) and tighten SET SCREW (2) to secure SPOUT (3). CONVERT TO A FIXED SPOUT IF DESIRED. Fig. B. 7420.101 ONLY. SPOUT CAN BE FIXED OR SWIVEL. 1 3 2 VIEW "A" DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. CARE INSTRUCTIONS: Fig. A. Fig. B. 3 M965016 REV.1.7 Speed Connect™ Drain Troubleshooting Guide Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration. Fig. B. Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D. Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E. The Stopper can now be removed by lifting it out of the Drain. Fig. F. CAM CAM CAP CABLE ADJUSTMENT PROCEDURE If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your St...

Baixe o seu

Para fazer o download, introduza 2 dígitos :