These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communication. Operation of this equipment in residential area is likely to cause harmful interference in which case the user will be required to correct the interfere

Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel. Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy network down time and/or permanent damage to hardware. • Use the command udprelay_do_systrace = 0 to disable systrace and enable console output. • Use the command C = x (where x=1 to 9.) This increases the levels of udprelay debug. A level of 5 will display the source, destination IP, and MAC lines se

After you click ‘Apply’, the following message will be displayed on your web browser: Please wait for about 30 seconds, then click ‘OK!’ button. You’ll be back to router management interface again, and the router is ready with new settings. 3-2-5 UPnP Setting This function enables network auto-configuration for peer-to-peer communications, with this function, network devices will be able to communicate with other devices directly, and learn about information about other devices. Many network dev

02 Status Change Note Short Title Released B D Fa a22855 CD — UG Speed Touch Home All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. 2 / 88 ▼ I1W1I1I 3EC 17058 AAAA TCZZA Ed. 02 Contents Contents 1 Welcome to the Speed Touch Home....................................7 1.1 Conventions....................................................................8 2 Speed Touch Home Tour ..

Alcatel-Lucent9900WirelessNetworkGuardian To illustrate, Figure 1a depicts the normalized bandwidth consumed by applications running on a commercial wireless network. By comparison, Figure 1b depicts the same applications on the same day relative to the cellular airtime consumed in the network to support these loads. Today’s monitoring and packet inspection products allow wireless service providers to monitor subscriber and application usage behavior on their network (Figure 1a) Figure 1a. Appli

2 Package Contents & System Requirements 2.1 Package Contents 2.2 System Requirements 2.2.1 Win-CE based PDAs (Pocket PC Device) .. PDA with Windows Pocket PC 2002 and Windows Mobile 2003 with at least 32 MB memory. .. Secure Digital I/O (SDIO) capable slot, check with your PDA manual or manufacturer. Go to for PDA compatibility. .. Microsoft Active Sync should be installed. .. A standard 802.11b or 802.11g Wi- Fi approved Access Point (AP)/Base station. 3 Introducing WL11-SD Card 3.1 WL11-SD cl

Null Route to IPMRM V2 192.168.13.25-255.255.255.255 dvmrpRecvIpmrmSGInfo: V2 Lookup ipsa 192.168.13.25 ipda 224.2.178.69, tsrc 0.0.0.0 Found route 192.168.13.0 to ipsa Route looks good Lookup S,G 192.168.13.25-255.255.255.255 224.2.178.69 on rib dvmrpRecvIpmrmSGInfo: V2 S,G found 192.168.13.25 224.2.178.69 Prune state pending, send another Prune dvmrpSendPrune: Learned S,G from non-local route, upstrGw=192.168.11.2 dvmrpSendPrune: Unable to find nbr for Prune. Null Route to IPMRM V2 192.168.13.

All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of AmbiCom, Inc. AmbiCom, Inc makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merc