Assessments - , GPA:
(
)
)
Fabricante : Grizzly
Arquivo Tamanho: 4.02 mb
Arquivo Nome : 1cec40ee-0d2d-26e4-9186-24cf630e91a6.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
The large size of the foot pads distributes the weight of the machine to reduce strain on the floor. Machine mounts for this machine use Grizzly Model G7158. Figure 7. Typical lag shield anchor and lag bolt. Figure 8. Typical anchor stud. Figure 9. Machine mount example. G0489 Metalworking Sander -13- Mounting Sander This step may require three people to complete— two to lift and hold the sander in place, and one person to install the hardware. Components and Hardware Needed: Qty Sleeve................................................................1 Hex Bolt M12-1.75 X 30.....................................1 Hex Nut M12-1.75..............................................1 Flat Washers 12mm..........................................2 Helpers..............................................................2 Angle Adjustment Lever....................................1 To mount the sander to the base: 1. Set the base in the upright position. 2. Slide the sleeve through the holes so it spans the width of the base yoke. 3. With the aid of a couple helpers, lift the sander, spread the yoke on the sander slightly and set onto the base (see Figure 10). 4. Slide the 30mm bolt and washers through the sleeve and tighten the nut. 5. Thread the angle adjustment lever through the slot and tighten the sander in position. Spark Trap, Rest & Eye Shield Theses components MUST be mounted before operation. Components and Hardware Needed: Qty Spark Trap ......................................................... 1 Eye Shield.........................................................1 Rest...................................................................1 Rest Lever.........................................................1 Square Nut ........................................................ 1 Cap Screw M5-.8 x 50.......................................1 To mount the spark trap, rest, & eye shield: 1. Refer to Figures 11-13. Figure 10. Base installation. Figure 11. Spark trap installation. Figure 12. Eye shield installation. -14- G0489 Metalworking Sander Figure 13. Rest installation. Dust Collection ACAUTION DO NOT operate the Model G0489 with a dust collection system that has been previously used for wood dust collection or other combustible material. Hot metal sparks and fragments could cause material to ignite! DO NOT attach to plastic fittings or dust collection system not rated specifically for metal dust collection! The Model G0489 comes with a 4" dust port ready to attach to your metal dust collection system. Your dust collection system is unique so we cannot give you specific instructions to cover all the possible set up options. To connect a dust collection hose: 1. Fit your dust hose over the dust port and secure in place with a hose clamp. Test Run Once the assembly is complete, test run your machine to make sure it runs properly. If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately. If you cannot remedy a problem, contact our Tech Support at (570) 546-9663 for assistance. To test run the machine: 1. Connect the machine to the power source. 2. Make sure you have read the safety instructions at the beginning of the manual and that the machine is setup properly. 3. Make sure all tools and objects used during set up are cleared away from the machine. 4. Turn the machine ON. 5. Listen to and watch for abnormal noises or actions. The machine should run smoothly with little or no vibration or rubbing noises. —Strange or unusual noises should be investigated and corrected before operating the machine further. Always disconnect the machine from power when investigating or correcting potential problems. G0489 Metalworking Sander -15- SECTION 4: OPERATIONS Operation Safety Awarning Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always wear safety glasses, a respirator, and hearing protection when operating this machine. Awarning A /ln Loose hair and cloth- ing could get caught in machinery and cause seri- JT§ ous personal injury. Keep loose clothing and long hair away from moving machinery. NOTICE If you have never used this type of machine or equipment before, WE STRONGLY RECOMMEND that you read books, trade magazines, or get formal training before beginning any projects. Regardless of the content in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training. Angle Adjustment The sander can be angled up and down to meet your needs. Use the angle adjustment lever shown in Figure 14 to lock the sander in the angle you choose. Tighten securely so the sander will not move during operation. Figure 14. Angle adjustment lever. Rests The Model G0489 comes with two rests. A fixed rest sits just above the spark trap. The second sits above the platen and can be adjusted for use or to move it out ...