Se opp! V.r sa vennlig a forst gjennomlese noyaktig denne veiledningen for installasjonen og idriftsettelsen. Huomio! Lue tama ohje huolellisesti lapi ennen asennusta ja kayttoonottoa. Observera! Var god och las noga igenom denna handledning fore installering och idrifttagande.SV ENG FIN NO F ENG ENG Contents 11 Tool Dimensions/Cutting Speeds 1 Specifications 12 Jigs And Push Blocks 2 User Responsibility 13 Controls 3 Standard Delivery 13.1 Definitions 4 Optional Accessories 13.2 Mounting A Tool

Please make sure that the hexagon nut (item 4) on the left side of the machine has a left-handed thread, i.e. must be turned in a clockwise direction to undo. Changing the Grinding Wheel If the wheel needs replacement because it is worn down or you want to use a different type of grinding wheel, the mounted wheel is to be removed as shown in figure 7. Please make sure that the hexagon nut (item 4) on the left side of the machine has a left-handed thread, i.e. must be turned in a clockwise direct

The grinder is to be subjected to a no-load trial run for at least 5 minutes. Do not stand in the grinder's danger zone during this trial run. Commissioning This double bench grinder is used for rough grinding. Please note that it is not intended for continuous operation. To prevent possible overloading/overheating it should not be operated for more than 15 - 30 minutes at a time. Let grinder cool down before operating again. Apply moderate pressure when holding the workpiece against the grindin

Please make sure that the hexagon nut (item 4) on the left side of the machine has a left-handed thread, i.e. must be turned in a clockwise direction to undo. Changing the Grinding Wheel If the wheel needs replacement because it is worn down or you want to use a different type of grinding wheel, the mounted wheel is to be removed as shown in figure 7. Please make sure that the hexagon nut (item 4) on the left side of the machine has a left-handed thread, i.e. must be turned in a clockwise direct

10 Connection to Power Mains L1 PE N 1~230 V / 50 Hz U1 Z1 Ha Hi C U2 Z2 red red yellow black Single-phase models: DS 125 W DS 150 W DS 175 W L1 PE 1~230 V / 50 Hz N U1 Z1 Ha Hi C U2 Z2 > n red red green black Single-phase models: DS 200 W L1 L2 L3 PE 3 ~ 400 V / 50 Hz U1 V1 W1 M 3~ Three phase current types: DS 175 D DS 200 D plain steelfine grindingderustingscrewdriverswood chiselsturning chiselsscissorscopperceramicsglassdeburringpolishingchiselsknivesdrill bitstungsten carbidealuminiumgrey i

It is recommended to check if an approval code is shown on the grinding wheel and to buy only approved grinding wheels. Metabo genuine grinding wheels are guaranteed for a constant high quality level. They are available at your metabo dealer in all common sizes and compositions. 5 1 Manufacturer’s address or stamp 2 Permissible speed in r.p.m. 3 Nominal size 4 Material (coded) 5 Test mark 6 Maximum working speed in m/s Grinding Wheel Check Before a new grinding wheel is mounted it should be subj

-From time to time re-measure the thickness of the metal of the work piece support. The support must be replaced if it is so worn that its thickness measures only 1.8 mm at any one point. 7 8 Machine Components Comment: Several constructive details distinguish these double grinding machines. The handling, described in the following, is in principle the same with all machines. 10 9 2 9 Wall bracket stock-no. 090 000 1150 10 Pedestal support base stock-no. 090 000 1134 Machine Installation The gri