|
Facilidade de uso
3. Always refer to the instruction manual for important details if the product is to be stored for an extended period. 4. Engine - 4 cycle. (Refer to engine manufacturer's operating instructions for fuel recommendations and additional information.) 5. Tires - Tubeless. Inflate to air pressure of 30 P.S.I. 6. Labels should be inspected before each use. Replace damaged labels immediately. Wire Check oil level regularly. Be sure correct oil level is maintained. Check oil level after every 5 hours of operation, or daily, before starting engine. Use SAE 30 Oil. Important: Change oil after first 5 hours of operation. This is extremely important to insure the long life of your Honda GC160 Engine. The GC160 breaks in and delivers full power quickly. The by-products of break in must be removed by changing the oil after the first five hours or operation, per Engine Manufactures recommendations. Remove drain plug and drain oil while engine is warm. Replace drain plug. Remove oil fill plug and refill with new oil. Start and run engine at idle for 30 seconds. Stop engine. Wait 30 seconds and re-check oil level. If required, add oil to overflowing at oil fill plug. Honda owners’ manual shows drawing of oil being drained from muffler side of engine. Little Wonder provides an oil drain slot in deck for draining oil from opposite side (gas tank side) of engine. Draining oil from gas tank side oil drain plug may be easier. Directions For Fan Removal: (This procedure must be done by qualified Little Wonder dealer) 1. Remove intake guard and front panel. 2. Remove bolt and washer securing fan to engine crankshaft. 3. The fan has a 3/4-16 nut welded on the fan hub. Insert a 3/4-16 grade 5 or grade 8 bolt and rotate this bolt to jack (or push) the fan off the engine. (Little Wonder part #910515 pressure screw is recommended.) 4. Reassemble using flat washer (#920503) and new bolt (#920502) with Loctite #242. To prevent accidental starting, remove spark plug wire when servicing engine or equipment. 5. Blower Bolt/Nut Torque Specifications Location Bolt / nut size P/N Min. torque Ft-Lbs (in-lbs) Max. Torque Ft-Lbs (in-lbs) Housing to engine face 5/16-24 x 3/4 flange head 910503 22 (264) 28 (336) Deck to housing 5/16-18 flange nut 114-B 16 (192) 22 (276) Engine to deck 5/16-18 x 1 gr 5 113 19 (228) 25 (300) Lower handle to deck 5/16-18 x 1.75 gr 5 942 19 (228) 25 (300) Upper handle to lower handle 5/16-18 x 1.75 gr 5 942 19 (228) 25 (300) Throttle to handle 1/4-20 X 1.5 gr 2 378 4 (48) 6 (72) Interior deflector to hook 10-32 x .625 flange head gr 5 329 (52) (71) Fan to crankshaft (95 oz) 5/16-24 x 1.75 hex head bolt gr 8 920502 16 (190) 18 (220) Fan to crankshaft (95 oz) 3/8 - 24 x 1.5 flange head gr 5 910518 39 51 Front panel to housing (short stud) 5/16-18 flange nut 114-B 16 (192) 22 (276) Intake guard clamp (long stud) 5/16-18 muloc nut 114-C — 8 (100) Wheel bracket to housing 5/16-18 flange nut 114-B 16 (192) 22 (276) Front wheel axle bolt 3/8-16 x 5.25 gr 5 900501 34 45 Parts Explosions Key# Part# Description 9502 Quantity 9602 Quantity 1 910610 Intake Guard Label 1 1 2 920600 5/16 - 18 Nylon Insert Nut 11 11 3 911130 Intake Guard Clamp 3 3 4 921100 Intake Guard Assy 1 1 5 114B 5/16 - 18 Serrated Flanged Lock Nut 14 14 6 921120 Front Panel 1 1 7 920502 5/16 - 24 x 1.75" hex head bolt gr 8 1 - 7 910518 3/8 - 24 x 1.5 flange head gr 5 -1 8 920200 5 HP Fan SHO Assy 1 - 8 920208 6 HP Fan SHO Assy -1 9 117 Key 3/16 x 3/16 x 1" 1 - 9 915 Key 1/4 x 1/4 x 2" -1 10 920503 Washer, 5/16 flat, thick 1 1 6. Key # 2 5 14 14 15 16 17 18 19 21 22 23 24 25 26 30 31 32 33 34 35 36 58 Part # 114C 114B 910916 910914 946 910301 900301 900302 179 910526 972 920300 312 405-1 932-1 916-2 163 920007 920009 942 129D 113 934B Description 5/16-18 Nylon Insert Nut 5/16-18 Serrated Flanged Lock Nut 5 HP Honda Engine Honda 6 HP Engine Briggs Throttle Clip Throttle Cable Upper Handle Grip (set of 2) 1/4-20 x 1 3/4 HHCS gr5 10-32 x 3/4 Self tapping Sheet Metal Screw 1/4-20 2-Way Lock Nut Pneumatic Wheel Offset,12" DIA Assy Retaining Ring 5/8 SAE Flat Washer Axle Lower Handle 5/16 Flat Washer 6/8/10 HP Right Blower Deck 6/8/10 HP Left Blower Deck 5/16-18 x 1.75 HHCS gr5 5/16 Regular Split Lock Washer 5/16-18 x 1.5 HHCS Pneumatic Wheel Bearing 9502 Quantity 11 14 1 - 1 1 1 1 1 1 1 2 2 2 1 2 12 1 1 8 4 4 6 9602 Quantity 11 14 - 1 1 1 1 1 1 1 1 2 2 2 1 2 12 1 1 8 4 4 6 7. Key# Part# Description 9502 Quantity 9602 Quantity 5 114B 5/16-18 Serrated Flanged Lock Nut 14 14 10 920000 5 HP SHO Housing 1 1 11 920602 Little Wonder Housing Label - 5 HP -1 11 910629 Little Wonder Housing Label - 6 HP 1 - 12 920603 SHO Warning Label 1 1 13 910503 5/16-24 x 3/4 Whiz Head Flange Bolt 4 4 20 973 10-32 2-Way Lock Nut 6 6 37 910130 Deflector Spring 1 1 38 8-18 Retaining Ring 3 3 39 910131 Knob 1 1 40 963 5/16 External Tooth Lock Washer 1 1 41 910100 6 HP Side Deflector 1 1 42 329 10-32 x 5/8 Serrated Flange Screw 2 2 43 910105 6 HP Internal Deflector 1 1 44 910132 Deflector Hand...
Este manual também é adequado para os modelos :Sistemas de ventilação - High Output Blower (671.57 kb)