Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
Do not operate blower when fatigued. 3. KEEP HANDS AWAY FROM AIR INTAKE AND AIR OUTLET CHUTE — Keep both hands on handles when power is on. 4. MAINTAIN AND EXAMINE BLOWER WITH CARE — Follow maintenance instructions given in manual. Do not use the blower if the muffler is defective or missing. 5. STORE BLOWER INDOORS — When not in use, store blower indoors in a sheltered, dry area where it’s not accessible to children. The blower, as well as fuel, should not be stored in a house. Keep throttle in the stop position. 6. BE SURE BLOWER IS FULLY ASSEMBLED — Never operate blower without all guards and deflectors in place. Ensure that all nuts, bolts, screws are installed and properly tightened. 7. KEEP THE THROTTLE IN THE “STOP” POSITION WHEN NOT IN USE. Always keep a safe distance between two or more operators when working together simultaneously. WARNING DANGER 1. DANGER ROTATING FAN - KEEP HANDS AWAY. DON’T ATTEMPT TO REMOVE MATERIALS FROM INTAKE OR DISCHARGE WHEN BLOWER IS RUNNING. WARNING DANGER 2. DANGER - DO NOT INSTALL OR REMOVE ATTACHMENTS WHILE BLOWER IS RUNNING. TURN OFF ENGINE TO MAKE CHANGEOVER. BE SURE THROTTLE IS IN THE STOP POSITION, AND THE BLOWER HAS COME TO A COMPLETE STOP. REMOVE THE SPARK PLUG WIRE BEFORE REMOVING MATERIAL. WARNING DANGER 8. WARNING! IN ORDER TO AVOID ENGINE DAMAGE DUE TO OVER-HEATING OR OVERREVVING, KEEP ENGINE RECOIL STARTER ASSEMBLY, THE BLOWER INTAKE AND OUTLET AREAS CLEAR AND FREE OF LEAVES OR OTHER DEBRIS. 3. C. Engine/ Fuel Warnings - "Don’ts" Blower Assembly Instructions WARNING DANGER HANDLE FUEL WITH CARE, IT IS HIGHLY FLAMMABLE. FUELING A HOT ENGINE OR NEAR AN IGNITION SOURCE CAN CAUSE FIRE AND RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE. 1. Do not smoke while handling fuel. 2. Do not refuel a hot or running engine. 3. Do not fill tank indoors. 4. CAUTION — Do not start or run engine indoors as poisonous carbon monoxide is emitted. 5. Do not operate in unventilated area. 6. Do not use the blower when electric system causes spark outside the cylinder. Check spark plug from time to time. When checking, keep plug a safe distance from cylinder to avoid burning of evaporated fuel from cylinder. D. Engine/ Fuel Warnings - "Do’s" 1. HANDLE GASOLINE WITH CARE. IT IS HIGHLY FLAMMABLE. Refuel before starting work. 2. Always use fresh gasoline. Stale gasoline can cause leakage. 3. Always pull starter cord slowly until resistance is felt. Then pull cord rapidly to avoid kick-back and prevent arm or hand injury. 4. Replace gasoline cap securely. If fuel is spilled move blower and fuel container from area and do not create a source of ignition. 5. Avoid spilling fuel or oil. Always wipe unit dry before using. Move at least 10 feet away from the fueling point before starting engine. 6. Always store gasoline in an approved container. Fill tank outdoors with extreme care. *NOTE : Numbers in brackets (#) represent Key Numbers shown on Parts List, and parts explosion. See pages 9-11. 1. Install lower handles (30) on top of deck (32, 33). Secure with four cap screws 5/16-18 x 1 3/4 (34), four 5/16 flat silver washers (31), and four 5/16-18 nylon nuts (2), finger tight. 2. Install upper handle (17) with four cap screws 5/16-18 x 1 3/4 (34), eight 5/16 washers (31), and four 5/16-18 nylon nuts (2), finger tight. Tighten lower handle nuts and bolts. Tighten upper handle nuts and bolts until the lower handle tubing pinches the upper handle. It will be normal for the lower handle tubing to crush slightly. 3. Attach throttle cable to upper handle with 1/4-20 x 1 3/4" cap screw (19) and 1/4-20 lock nut (22) through hole on upper handle (17). It will mount on the left. Insert the 1032 x 3/4" self-tapping screw through the hole of the throttle control and into the pilot hole in the handle and tighten. (NOTE: Over tightening the screw on the left hand mounted controls could cause damage to the control.) Once the 10-32 screw is tightened, go back to the 1/4-20 screw and tighten it enough to get a smooth action in the control. If the throttle does not maintain it’s setting once you start the engine, tighten this screw some more. Connect throttle clip (15) to upper handle. 4. Tilt blower back on handle and install front wheel bracket (51) over the three studs on lower front of blower housing. Secure with three 5/16-18 flange nuts (5). 5. Insert pneumatic wheel sleeve (53) in front pneumatic wheel (52). Install pneumatic wheel spacers (54) over the axle sleeve on both sides of wheel and install in front wheel bracket (51). Insert 3/8-16 x 5 1/4 axle bolt (50) through wheel bracket and axle sleeve. Secure with 3/8-16 axle nut (49). WARNING DANGER ALL LITTLE WONDER BLOWERS ARE SHIPPED WITHOUT OIL. WHEN FILLING OIL - USE SAE 30 OIL. REFER TO ENGINE MANUFACTURES INSTRUCTION MANUAL FOR PROPER ENGINE OPERATION INSTRUCTIONS. 4. Operating Instructions Maintenance Instructions Con’t Refer to Engine Manual for Engine Operation. Little Wonder recommends using SAE 30 Oil. The use of multi-viscosit...
Este manual também é adequado para os modelos :Sistemas de ventilação - High Output Blower (671.57 kb)