Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. GENERAL SAFETY INFORMATION When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to person, including the following: 5. Sufficient air is needed for proper combustion and exhausting of gases WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND through the flue (chimney) of fuel burning equipment to prevent back INJURY TO PERSON, OBSERVE THE FOLLOWING: drafting. Follow the heating equipment manufacturer’s guideline and safety 1. Read all instructions before installing or using range hood. standards such as those published by the National Fire Protection Association (NFPA) and the American Society for Heating, Refrigeration, 2. Use this unit only in the manner intended by the manufacturer. If you have and Air Conditioning Engineers (ASHRAE), and the local code authorities. questions, contact the manufacturer. 3. Before servicing or cleaning the unit, switch power off at service panel CAUTION: FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO and lock the service disconnecting means to prevent power from being EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND VAPORS. switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to 6. To avoid motor bearing damage and noisy and/or unbalanced impellers, the service panel. keep drywall spray, construction dust, etc. off power unit. 4. Installation work and electrical wiring must be done by qualified person(s) 7. Refer to the instructions included with the Range Hood Canopy for additional in accordance with all applicable codes and standards, including fire- safety information. related construction. INSTALLATION INSTRUCTIONS CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE STARTING INSTALLATION. WARNING: THIS BLOWER IS INTENDED FOR USE ONLY IN AIR KING PROFESSIONAL SERIES RANGEHOOD CANOPIES MARKED SUITABLE FOR USE WITH THIS BLOWER. DO NOT TO INSTALL IN ANY OTHER APPLICATION. SECTION 1 Preparing for installation NOTE: Before installing blower, make sure range hood canopy is properly installed and securely in place. See “Range Hood Mounting Instructions”. 1. Unpack blower from the carton and confirm that all pieces are present. In addition to the blower you should have: 8 - 8-32 Screws 8 - Washers 1 - Fuse 1 -Instruction/Safety Sheet 2. The installation of the blower is slightly different from one canopy height to another. For 18" high canopies proceed to Section 2, for 10" high canopies proceed to Section 3. SECTION 2 Installation into 18" High Canopy 1. Lift blower up into the hood canopy and slide the keyhole slots in the motor mounting flange over the two studs of the hood. Slide the motor into place and tighten the hex nuts on the mounting stud while lining up the 8 holes in the motor mounting flange to the 8 screw studs of the hood (Figure 1). Figure 1 Keyholes Stud w/Hex Nuts Screw Stud SAVE THESE INSTRUCTIONS 111597005 New 3-07 1 of 8 2. Using the included 8-32 screws and washers, mount the blower in place 4. Plug both the 3 wire and 4 wire quick connect cords from the blower into and tighten all screws. Confirm that the blower is securely seated in place the appropriate receptacles located on the inside front of the hood canopy. and there are no air gaps around the blower gasket. These cords will only fit into the receptacles one way (Figure 2). 3. Plug both the 3 wire and 4 wire quick connect cords from the blower into 5. Reinstall the rear bottom plate by fitting the back edge of the plate into the the appropriate receptacles located on the inside front of the hood canopy. channel located on the back of the hood and reinstalling the two screws These cords will only fit into the receptacles one way (Figure 2). and washers removed in Step 1(Figure 4). Receptacles Figure 2 Blower SECTION 3 Installation into 10" High Canopy 1. Remove the rear bottom plate of the hood canopy. It is secured in place with a screw and washer on either side (Figure 3). Figure 3 Screw Bottom Plate Washer 2. Lift blower up into the hood canopy and slide the keyhole slots in the blower mounting flange over the two studs of the hood. Slide the blower into place and tighten the hex nuts on the mounting stud while lining up the 8 holes in the blower mounting flange to the 8 screw studs of the hood (Figure 1). 3. Using the included 8-32 screws and washers, mount the blower in place and tighten all screws. Confirm that the blower is securely seated in place and there are no air gaps around the blower gasket. Fuse Figure 5 Cap Channel Figure 4 Screw Bottom Plate Washer SECTION 4 Finishing the Installation 1. Install the included fuse into the electrical panel by turning the fuse cap counter clockwise and pulling out. Insert the included 1/4" x 1-1/4" time delay fuse in t...