Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
Then, two tubes together until tube is securely seated in tube (about 3 inches). Upper Tube Lower Tube ATTACH THE COLLECTION BAG restrictor 3.Turntheinletcounterclock-Slide the opening of the collection bag removetheunit.Do wiseanditfromover the blower outlet. Pull the velcro notclosetheinletdoor.Youwillnext strap tightly through the buckle and se attachthetubes. vacuum cure to the velcro tabs. NOTE: Make sure the velcro strap is located on the blower outlet as shown below. Also, make sure the zipper on the bag is completely closed. Vrte°toomver _rleettrictor Z' _[_"_" ATTACHING THE VACUUM TUBES There are 2 vacuum tubes, an upper and lower tube. The upper tube is cut straight on both ends and attaches to the blower unit. The lower tube at taches to the upper tube, and has an angled end that you point toward the ground during vacuum use. 1. Ensure unit is stopped and extension cord is unplugged. 2. Locate the arrows on the upper vacuum tube and on the vacuum inlet area of the unit. Upper Vacuum Tube Velcro Strap _ / i Coll_ _.._ Bag _ Blower Outlet ADJUSTING THE SHOULDER STRAP ON THE COLLECTION BAG 1. Carefully loop the shoulder strap through the buckle as shown in the illustration below. Last in t_ 2.Positionright-handtheunitonyour side,bloweroutletandbagpointing towardtherear.Holdtheunitinan uprightwiththelower positionvacu umtubeonthegroundit. tosupport 3.Placetheshoulderoverstrapyour headandontoyourleftshoulder. 4.Adjustthestraptoallowafreeflow ofairfromtheblower. Ifthecollec tionbagiskinked,willnot theunit operate properly. NOTE:Thestrapisdesigned toposition thecollectionbagonyourshoulder with- outkinks.Theisnotintended strapto supportoftheunit. theweight Shoulder strap on left shoulder No kinks in bag allows free air flow HOW TO CONVERT UNIT FROM VACUUM USE TO BLOWER USE 1. Stop unit and unplug tile extension cord. 2. Remove the vacuum tubes and collection bag. 3. Install the inlet restrictor that was removed when assembling for vacuum use. NOTE: If you are unable to locate the inlet restrictor, the unit will still operate. This restrictor improves function. 4. Close the inlet cover it is latched closed. 5. Re-install the blower the blower and make sure tubes. Refer to the section ATTACHING THE BLOWER TUBE/NOZZLE for instructions on how to attach this item. SELECT AN EXTENSION CORD Use only a 120 A.C. voltage supply as shown on nameplate of the unit to power your blower. • To reduce the risk of electrical shock, this equipment has a polarized plug (one blade is wider than the other) and will require the use of a polarized extension cord. The appliance plug will fit into a polarized extension cord only one way. If the plug does not fit fully into the extension cord, reverse the plug. If the plug still does not fit, obtain a correct polarized extension cord. A polarized extension cord will require the use of a polarized wall outlet. This plug will fit into the polarized wall outlet only one way. If plug does not fit fully into the wall outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper wall out let. Do not change the equipment plug, extension cord receptacle, or extension cord plug in any way. The extension cord used to reach the power source must be: • Specifically marked as suitable for outdoor use. The cord must be marked with the suffix WV-A" (in Canada "W"). • Heavy enough to carry current from the power source the full length of extension cord to the unit. Otherwise, loss of power and overheating can occur causing damage to unit. Refer to table for minimum wire gauge recom mendations. The cord must be marked with the proper wire gauge. (Appropriate extension cords are available.) Do not use multiple cords. • In good condition. Cord insulation must be intact with no cracks or deterioration. Plug connectors must be undamaged. DO NOT use multiple cords. MINIMUM WIRE GAUGE RECOMMENDATIONS 50 F'R 100 FT. A.WG* A W.G.* 16 14 *American Wire Gauge Secure the extension cord to the unit by tying the cord onto the cord retainer. Insert the cord receptacle in to the recessed plug. Cord Retainer f ',_J Ij[. ""-__J_.._-f_.._ Recessed Cord onUni Receptacle ._l I _!e KNOWELECTRIC YOURBLOWER READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations to your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. MULCHING BLADES As a standard feature, the impeller on your blower also functions as a mulcher. When using the vacuum attachment, the impeller/mulcher automatically reduces debris at a ratio of up to 16:1. Cord Retainel Top Handle _,, _1_ ON/OFF Switch Collection Bag Rear Handle Inlet Cover Latch Blower Tube/Nozzle Inlet Restrictor _4,-_ Upper Vacuum Tube Lower Vacuum Tube ON/OFF SWITCH BLOWER TUBE/NOZZLE The ON/OFF SWITCH is used to The BLOWER TUBE/NOZZLE is deactivate the motor. signed to direct the flow of air. INLET COVER LATCH INLET RESTR...
Este manual também é adequado para os modelos :Sistemas de ventilação - 358.799430 (932.96 kb)