Assessments - , GPA:
(
)
)
Fabricante : Panasonic
Arquivo Tamanho: 1.79 mb
Arquivo Nome : UB7325.PDF
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
3 Open the paper cover and insert ordinary Letter test paper, then close the paper cover. • Loading Copy Paper procedure (refer to the Operating Instructions on page 11) “ ” lights up. (Normal operation) (If not) Check copy paper. 4 Open the printer door. “ ” flashes. (Normal operation) (If not) *1 5 Close the printer door. “ ” lights up. (Normal operation) (If not) *1 6 Press . Press . Screen is fed. (Normal operation) The screen film surface is not fed smoothly. *1 There are strange noises. 7 Use the accessory marker to draw a large filling the entire copyable area of the screen film surface. • Copyable area (refer to the Operating Instructions on page 7) Press twice. Press . “ ” lights up and three copies are made. (Normal operation) Three copies are not made. *1 The entire readable area is not printed. There are strange noises or paper jams during the copying process. Multiple sheets of paper are fed through at the same time. 8 Press to move the screen film surface. Write letters, etc. with the marker. Press once. Press . The Contrast/Remaining Film indicator light is turned on and one copy is made. (Normal operation) The Contrast/Remaining Film indicator light is not turned on. *1 The image is not copied properly. There are strange markings on the copy sheet (e.g., stripes or lines). 9 Press once. The Contrast/Remaining Film indicator light is turned off. (Normal operation) (If not) *1 *1 Contact the store or dealer from which the unit was purchased. 35 Installation Manual Repacking Perform Assembly Steps 2 through 4 on pages 31 - 33 in reverse to repack the electronic board and accessories. Use the joints to fasten the shipping box. • Do not touch the screen film surface, as this may damage it. Eraser Thermal transfer film Manuals CD-ROM Power cord Markers Joints Joints Joints Joints Joints Joints Electronic board Shipping box Shipping box Caution Assembling the Optional Stand (KX-B061) ¦ Accessories The package box for the optional stand includes the parts noted below; please confirm that all parts are present before beginning installation . No. Part name Illustration Q’ty No. Part name Illustration Q’ty Stand base 2 Wing bolt M5 x 12 mm (15/32”) 6 Pipe 2 Support bracket 2 Cover 2 Fall-prevention extension leg 4 Side bar (A) 2 Screw M6 x 60 mm (2 3/8”) 4 Side bar (B) 1 Nut 4 Screw M8 x 45 mm (1 25/32”) 12 Wrench *1 1 Fixture (left) 2 Wing bolt (Not use*2) M4 x 8 mm (5/16”) 8 Fixture (right) 2 Screen holder bracket (Not use*2) 4 *1 The accessory wrench is required to fasten or loosen the screws , ; please store it carefully for future use. *2 These are used for other models. .Before assembly, be sure to lock the casters. Locking the casters (Push this side) Releasing the lock Assembling the Optional Stand (KX-B061) 37 Installation Manual ¦Assembly 1 Assembling the stand ¦Assembling the fall-prevention extension legs The fall-prevention extension legs increase the safety of the electronic board. • Install and always set the fall-prevention legs when using the stand. • When tightening the screw , hold the nut with pliers. Note • When folding back the fall-prevention extension legs to release the lock, perform as follows. ¦Inserting the covers to the pipes Fall-prevention extension legs • Caster locks are attached to the back side. Caution 1 1 2 Assembling the Optional Stand (KX-B061) ¦ Assembling the stand Assemble with the holes toward the front. Locking casters side (rear) Pull the fall-prevention extension legs down (fall-prevention extension legs will be fixed by the lock pin.) 1 1 1 2 Locking casters side (rear) Note *1 Do not tighten the screw too much. This may deform the pipes. Assembling the Optional Stand (KX-B061) Attach the fixtures with the four wing-bolts. Assemble and install the electronic board. 3 Refer to step 3 on page 32. Installation 39 Optional Wall-mounting Kit (KX-B063) Before attempting installation of this wall-mounting kit, we strongly recommend consulting with the building manager, engineer, or architect. The installer needs to know the type of construction used for the wall intended for this installation and the location of wall studs. Selection of hardware is critical for safe wall-mounting, and depends on the nature of wall construction. Installation should not occur until this consultation takes place. Caution • Do not attach the electronic board to mortared walls. Accidental electric leakage from the wall-mounting fixture bolts to metal laths or wire laths can cause heat, smoke or a fire. 1. Tools required: A minimum of eight (8) pieces of appropriate wall-support hardware (molley, toggle, etc.) NOTE: THIS HARDWARE MUST BE LOCALLY PROCURED, IT IS NOT INCLUDED IN THE KIT. Drill (and drill bit of correct size) for hardware installation Screw driver (Both phillips (+) and slotted (–) will be required.) Tape measure Tape or thumb-tacks (2 pcs) Bubble type level 2. Pre-requisites 1. Before installation, make sure that the wall intended for installation is capable of supportin...