12-Lb. Weight at 2, 4, and 6 MPH 2 MPH 4 MPH 6 MPH Act u al De pt h of Weigh t ( ft.) Amount of Cable in Water (ft.) 4 MPH 6 MPH Amount of Cable in Water (ft.) A c tualDepth of W e ight ( ft.) 2 MPH 8-Lb. Weight at 2, 4, and 6 MPH 2 MPH 4 MPH 6 MPH Act u al De pt h of Weigh t ( ft.) Amount of Cable in Water (ft.) Blowback Charts 10-Lb. Weight at 2, 4, and 6 MPH 13 Adjusting the Depth Meter The Cannon Depth Meter provides non-slip accuracy, plus easy resetting. To reset, just slide the meter away

In Canada, parts may be ordered from any of the Canadian Authorized Service Centershown on thenclosed list. Be sure to provide the MODEL and SERIAL numbers of your downriger when ordering parts. Please use the corect part numbers from the parts list. Payment for any parts ordered from the CANON parts department, may be by cash, personal check, Discover Card, MasterCard or VISA. Torder, cal 1-80-27-643 or FAX 1-80-527-464. > PART OF ASSEMBLY > ITEM CANOT BE SOLD SEPARATELY * PARTS USED BUT NOT SH

Examine the top of the terminator and note the Unwind about 2 feet of cable order shown in the detail to run cable. and thread the cable through the rubber cushion. Lead cable into HOLE A. Pull six inches of cable through. Thread cable through swivel, then up into bottom of the terminator. Lead cable out of HOLE B and into HOLE C. Push the cable until its end touches the inside of the terminator hook. HOLE A Swivel TIP: Use only straight cable, not kinked. Tighten cable by squeezing terminator u

Pistol grip release provides quick one hand up and down angle adjustment with 360 ° rotation with the push of the release button. Ratcheting adjustment system allows you to pull the rod holder straight up for rod removal. Clear anodized aluminum is used for strength and corrosion resistance and a UV resistant cap protects the finish of the rod and reel. This Adjustable Rod Holder is compatible with Cannon, Bert’s, and Traxstech track systems. 1907022 Adjustable – Downrigger Mount Rod Holder - Me

1904010 Gimbal Mount Track – Side Gunnel 1904011 Gimbal Mount Track – Stern Cannon’s Gimbal Mount Track allow for mounting of Cannon’s track system accessories in flush mount rod holders. Thirty degree angled gimbals have twelve inch tube length with an outer diameter of 1-1/2 inches. Eighteen inches of track allow for mounting up to three track system rod holders. The system is compatible with Cannon, Bert’s, and Traxtech track system products. Components are made from clear anodized aluminum a

JOHNSON OUTDOORS INC. DISCLAIMS LIABILITY FOR INCIDENTAL AND CONSEQUENTIAL DAMAGES, AND IN NO EVENT SHALL ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, EXTEND BEYOND ONE YEAR FROM THE DATE OF PURCHASE. THIS WRITING CONSTITUTES THE ENTIRE AGREEMENT OF THE PARTIES WITH RESPECT TO THE SUBJECT MATTER HEREOF; NO WAIVER OR AMENDMENT SHALL BE VALID UNLESS IN WRITING SIGNED BY JOHNSON OUTDOORS INC. Some states do not allow limitations on how

warrants to the original purchaser that the accompanying product (see exclusions below) is free from defects in material or workmanship for a period of one (1) year from the date of purchase. Within the warranty period, Johnson Outdoors Inc. will, at its option, either repair or replace same without charge (but no cash refunds will be made). The unit must be returned, prepaid and with proof of the date of purchase to the following: . Johnson Outdoors, Inc Cannon Division, 121 Power Drive, Mankat

Bearing system ensures smooth swivel action even while a downrigger weight is attached. Components are made from clear anodized aluminum and stainless steel for strength and corrosion resistance. The swivel base downrigger pedestals are compatible with Cannon, Bert’s, and Traxstech track systems. Available in 4” and 6” heights. Rod Holder \ Accessory Compatibility Mounts Rod Holde r Track Mount Gimbal Track Mount Pedestal Track Mount Rail Mount Clamp Mount Deck Mount Angled Fixed Mount . . . 0 0

1904020 Clamp Mount Cannon Rail Mounts allow for the mounting of Cannon single and dual axis rod holders to any transom or allowable clamping edge. Clamp opens to two and a half inches and is made from clear anodized aluminum and stainless steel for strength and corrosion resistance. 1904000 Deck Mount The Cannon Deck Mount plate is a four inch by three inch clear anodized aluminum plate which allows the hard mounting of Cannon Dual Axis Rod Holders. The plate comes with a black protective mount

NOTE: Do not return your CANNON accessory to your retailer. Your retailer is not authorized to repair or replace this unit. You may obtain service by: • calling CANNON at 1-800-227-6433; • returning your accessory to the Factory Service Center; 121 Power Drive, Mankato, MN 56001 Please include proof of purchase and purchase date for warranty service with any of the above options. Adjustable Dual Axis Rod Holder Shown Owner’s Manual TROLLING SYSTEM Rod Holders: ANGLED FIXED MOUNT Adjustable Singl