Assessments - 4, GPA: 4 ( )

Fabricante : Buhler Arquivo Tamanho: 1.84 mb Arquivo Nome : Língua de Ensino:

DO NOT attempt to start or troubleshoot this engine in any other way. Figure 29. Recoil Starter Cord Handle Page 14 4-Cycle • Snow King Engine 181-1275-14 VI. Stopping Your Engine and Short-Term Storage Stop engine according to equipment manufacturer’s instructions. !WARNING To avoid unsupervised operation of an engine, especially by children, NEVER leave it unattended when it is running. Always turn off the engine after use and remove ignition key, if provided. !WARNING NEVER store the engine with fuel in the fuel tank inside a building with potential sources of ignition such as hot water and space heaters, clothes dryers, electric motors, etc. A. Stop Engine NOTE Run engine for a few minutes to help dry off any moisture on engine before proceeding to Step 1. 1. Move equipment control, if present (see manufacturer’s instructions), engine control lever or ignition switch to “STOP” or “OFF” position. See Figure 31. !WARNING To avoid unsupervised operation of an engine, especially by children, NEVER leave it unattended when it is running. Always turn off the engine after use and remove ignition key, if provided. 2. Remove ignition key, if provided (see manufacturer’s instructions). See Figures 30 and 32. NOTE Removing key will reduce the possibility of unauthorized starting of the engine while equipment is not in use. 3. Be sure fuel valve, if present (see equipment manufacturer’s instructions) is in “OFF” position. See Figure 34 on page 16. Figure 30. Ignition Key STOP1 5 1. Engine Speed Control 2. “STOP” Position 3. “SLOW” Position 4. “RUN” Range 5. “FAST” Position 4 3 2 Figure 31. Engine Speed Control Positions Figure 32. Possible Ignition Key Locations STOPSTOPSTOPSTOPSTOP 181-1275-14 4-Cycle • Snow King Engine Page 15 B. After Engine is Stopped !WARNING To prevent possible freeze-up of engine controls, follow instructions with engine STOPPED, listed below. 1. Wipe all snow and moisture from engine control lever and choke areas. 2. Move equipment control, if present (see manufacturer’s instructions), engine control lever or ignition switch back and forth several times and leave control in “STOP” or “OFF” position. See Figure 33. 3. Move engine choke back and forth several times and leave in the “FULL CHOKE” position. See Figure 24 on page 12. Afterward, continue reading instructions below. 4. Be sure fuel valve, if present (see equipment manufacturer’s instructions) is in “OFF” position. See Figure 34. NEVER store the engine with fuel in the fuel tank inside a building with potential sources of ignition such as hot water and space heaters, clothes dryers, electric motors, etc. !WARNING STOP1 5 1. Engine Speed Control 2. “STOP” Position 3. “SLOW” Position 4. “RUN” Range 5. “FAST” Position 4 3 2 Figure 33. Engine Speed Control Positions Fuel Valve “OPEN” Position Shown Fuel Tank Turn Valve Clockwise To “OFF” Position Figure 34. Fuel Valve Positions Page 16 4-Cycle • Snow King Engine 181-1275-14 VII. Maintenance !WARNING An adult should perform maintenance on this engine. Only allow children to perform maintenance if an adult has determined they are experienced and capable of such operation. !WARNING To prevent accidental starting when working on equipment, always: • Carefully disconnect spark plug wire and keep it away from spark plug. See Figures 35 and 36. See "G. Avoid Accidental Starts" instructions on page 2. Afterward, continue reading instructions below. • Keep the disconnected spark plug wire securely away from metal parts where arcing could occur. • Carefully attach the spark plug wire to the grounding post, if provided. • Disconnect battery at negative terminal first, if engine is equipped with a D.C. electric starter. • Turn all engine switches to “OFF” position. • Remove ignition key, if provided. NOTES When disconnecting power cord, always disconnect power cord from outlet first; then disconnect power cord from switch box on engine. See Figure 37. When connecting power cord, always connect power cord to switch box on engine first; then into outlet. See Figure 37. A. Remote Choke See equipment manufacturer’s instructions and contact an Authorized Tecumseh Servicing Dealer. B. Changing Oil To avoid engine damage, it is important to: • Check oil level before each use and every 5 operating hours when engine is warm. See "A. Checking Oil Level" instructions on page 4. Afterward, continue reading instructions below. • Change oil after first 2 operating hours and every 25 operating hours thereafter. Engine should still be warm but NOT hot from recent use...

Baixe o seu

Para fazer o download, introduza 2 dígitos :