Assessments - 2, GPA: 3.5 ( )

Fabricante : Tecumseh Arquivo Tamanho: 1.84 mb Arquivo Nome : Língua de Ensino:

1. To prevent serious injury from fuel fires, empty fuel tank by running engine until it stops from lack of fuel. DO NOT attempt to pour fuel from engine. 2. Run the engine while waiting until the remaining fuel is consumed. !WARNING NEVER leave the engine unattended when it is running and NEVER run engine in enclosed areas. 3. Begin servicing the cylinder bore. See "II. Oil Cylinder Bore" instructions on page 25. Page 24 4-Cycle • Snow King Engine 181-1275-14 II. Oil Cylinder Bore !WARNING When lubricating cylinder bore, fuel may spray from spark plug hole. To prevent serious injury from fuel fires, follow these instructions: 1. Carefully disconnect spark plug wire and keep it away from spark plug. See Figures 53 and 54. • Keep the disconnected spark plug wire securely away from metal parts where arcing could occur. • Carefully attach the spark plug wire to the grounding post, if provided. • Disconnect battery at negative terminal first, if engine is equipped with a D.C. electric starter. • Turn all engine switches to “OFF” position. • Remove ignition key, if provided. 2. Remove spark plug. 3. Squirt 1oz. (30ml) of clean engine oil into spark plug hole. 4. Cover spark plug hole with rag to prevent fuel from spraying from spark plug hole when starter rope is pulled. NOTES For engines equipped with recoil starters proceed to Step 5. For engines equipped with electric starters proceed to Step 6. 5. Grasp starter cord handle: a. Pull starter cord handle out slowly using a full arm stroke. b. Repeat once. (This will distribute oil throughout the cylinder to prevent corrosion during storage.) c. Proceed to Step 7. 6. Push starter button or turn ignition switch key to “START” position. Immediately release starter button or turn ignition switch key to “OFF” position. (This will distribute oil throughout the cylinder to prevent corrosion during storage.) 7. Remove rag from spark plug hole. 8. Install spark plug. 9. Carefully disconnect spark plug wire from grounding post, if provided. See Figure 53. 10. Connect spark plug wire to spark plug. See Figure 54. III. Oil Change oil if NOT changed within the last 3 months. See "B. Changing Oil" instructions on page 17. IV. Battery See equipment manufacturer’s instructions for proper battery storage, if present. Figure 53. Disconnecting/Connecting Spark Plug Figure 54. Typical Spark Plug Connection 181-1275-14 4-Cycle • Snow King Engine Page 25 X. Preventing Forest, Brush and Grass Fires Local, state and federal laws may require use of a spark arrester to prevent fires. For example, it is a violation of California Public Resources Code (section 4442) to use or operate engine on any forest-covered, brush-covered or unimproved grass-covered land unless engine is equipped with a spark arrester. Spark arrester must be maintained in effective working order by owner and/or operator. To determine if your engine has a spark arrester, locate the muffler on your engine. For example, the muffler discharge will have a spark arrester cover that reads “Tecumseh Screen Type 36085”. If your engine does NOT have a spark arrester, you may purchase one from your Authorized Tecumseh Servicing Dealer. In some cases the muffler may need to be replaced to allow the spark arrester to be installed. XI. Maintenance Intervals Maintenance is one of the most important things that you can do to extend the life of your Tecumseh Engine. If you are unable to perform maintenance intervals yourself, consult your local Authorized Tecumseh Servicing Dealer, call 1-800-558-5402, or go to for additional information. ALWAYS promptly follow maintenance intervals listed in this manual. See Table 4. Table 4. Maintenance Intervals Procedure Time Change Oil After First 2 hrs. When Engine is Warm Check Oil Level 5 hrs. Or Before Each Use Clean Cooling Fins 5 hrs. Or Before Each Use Change Oil 25 hrs. Or 3 mos. Check Spark Plug 100 hrs. Or Seasonally Replace Spark Plug 200 hrs. Or Seasonally First Scheduled Maintenance After First 2 Hours When Engine is Warm 1. Change Oil Date_______________Owner/Dealer Page 26 4-Cycle • Snow King Engine 181-1275-14 Before Each Use Scheduled Maintenance Every 5 Hours or Before Each Use 1. Check Oil Level 2. Clean Cooling Fins Date_______________Owner/Dealer Date_______________Owner/Dealer Date_______________Owner/Dealer Date_______________Owner/Dealer Date_______________Owner/Dealer Date_______________Owner/Dealer Date_______________Owner/Dealer Date_______________Owner/Dealer Date_______________Owner/Dealer Date____...

Baixe o seu

Para fazer o download, introduza 2 dígitos :