Log:
Assessments - 3, GPA: 4.7 ( )

Instruções de Operação Craftsman, Modelo 1693219

Fabricante : Craftsman
Arquivo Tamanho: 3.31 mb
Arquivo Nome :
Língua de Ensino:
Ir para baixar



Facilidade de uso


Hair Pin (Lower Position) C. Gauge Wheel Bracket 31 Troubleshooting, Adjustment & Service Mower Adjustments Continued. Cutting Height Adjustment Note: To operate the electric cutting height motor, it is necessary to insert the ignition key and turn it to the on position.This may be safely done so long as the spark plug wires have been disconnected as noted in the WARNING at right. The key should be turned to off and removed when the step has been completed. Press the cutting height adjustment switch while observing the cutting height gauge on the left side of the mower to adjust the cutting height. Leveling The Mower If the cut is uneven, the mower may need leveling. Unequal or improper tire pressure may also cause an uneven cut. Tire pressure should be as follows: • Front: 12-15 psi • Rear: 6-8 psi SIDE TO SIDE LEVELING 1. With the mower installed, place the tractor on a smooth, level surface such as a concrete floor. Turn the front wheels straight forward. 2. Place the cutting height adjust in high-cut position. 3. Set the parking brake, turn off the ignition, and remove the key. 4. Check for bent blades and replace if necessary. 5. Arrange the mower blades so that they are pointing from side-to-side. 6. Measure the distance between the outside tips of each blade and the ground. If there is more than 1/8" (3mm) difference between the measurements on each side, proceed to step 5. If the difference is 1/8" (3mm) or less, proceed to Front To Back Leveling. 7. See Figure 47. Loosen the outside nut (A) then turn the eccentric nut (B) to raise or lower the left side of the deck. Repeat on the right side of the deck. When the mower deck is level, hold the eccentric nut while tightening the outside nut. FRONT TO BACK LEVELING 1. Arrange the blades so they face front-to-back. 2. Measure the distance from the ground to the front and rear tips of each blade. The measurement should be equal for both blades. Front tips should be 1/8” to 1/4” higher that the rear tips. If not, proceed to step 3. 3. Loosen the two rear jam nuts on both both arm assemblies (see Figure 48). Adjust the jam nuts on both arms until the mower deck is level or the front is 1/8” to 1/4” higher. WARNING Before checking mower, shut off PTO and engine. Allow all moving parts to stop. Remove ignition key, then disconnect the spark plug wires and fasten them away from the spark plugs. Figure 47. Side-to-Side Adjustment A. Outside Nut B. Eccentric Nut A B Starting Position Max 1/4 Turn to Lower Side of Mower Max 1/4 Turn to Raise Side of Mower A Figure 48. Front to Back Leveling A. Jam Nuts 32 Troubleshooting, Adjustment & Service BELT ROUTING VIEWED FROM TOP To avoid damaging belts, DO NOT PRY BELTS OVER PULLEYS. MOWER BELT REPLACEMENT 60” Mower Drive Belt Replacement 1. Remove the mower deck. See Mower Removal and Installation 2. Remove the screws securing both deck covers and remove the covers. Figure 49. 60” Mower Deck Belt Routing Center Pulley Belt Double V Outer Pu...

Este manual também é adequado para os modelos :
Snow Blowers - 1692871 (3.31 mb)
Snow Blowers - 1692870 (3.31 mb)
Snow Blowers - 1692872 (3.31 mb)
Snow Blowers - 1693112 (3.31 mb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias