Assessments - 5, GPA: 3.8
(
)
)
|
Facilidade de uso
• To reduce the travel speed, press down on the side handle. Working on slopes ! Risk of injury from machine tipping over Work slowly and carefully, especially when you change direction. Guide the machine up or down the slope, not crosswise to it. Watch out for obstacles, do not work near inclines. Do not use the machine on slopes with a gradient greater than 20 %. Tips on clearing snow • Clear snow immediately after it has stopped snowing; later on, the underneath layer will ice up and will make clearing the snow more difficult. • If at all possible, clear snow in the direction of the wind. • Clear the snow in such a way that the tracks you have cleared overlap slightly. Set the direction and distance of throw Figure 10 ! Risk of injury Do not set the flap (2) of the throw- out chute (3) in the direction of people, animals, windows, cars and doors. Set the direction of throw (STH 5.56, STH 8.66, STH 10.66 C) • Put the throw-out chute (3) in the desired direction by rotating the handle (Figure 1, item 7) (STH 953) • Turn the ejection chute in the desired direction with the handle (7). ! Risk of damage Do not use the handle (7) to lift the machine. Set the throw distance The steeper the angle of the flap (2) is set, the higher and further the snow will be ejected. • For machines with lever (Figure 1, item 5): press lever forwards to set the flap (2) higher and back for lower. • For machines without lever: loosen knob (1) and set flap (2) higher or lower as required. Operating Manual – Snowthrower English Start the engine Figure 2 ! Danger If you start the engine in an enclosed space, move the machine immediately afterwards into the open air. Never leave the engine running in an enclosed space. Before starting the engine, release coupling levers (Figure 1, items 1 and 2)/coupling bar (Figure 1, item 1). • Check contents of fuel tank and oil level, as required fill up with oil and fuel (see “Engine instructions”). Start with pull starter • Set shut-off valve (10), if this is present, to “ON”. • Put spark-plug connector (8) onto the spark plug. • (STH 5.56, STH 8.66, STH 10.66 C) Set throttle lever (7) to “ ”. • For a cold start, set choke (2) to “”/“ON”. • Insert ignition key (1) in the ignition lock. In (STH 953), also turn to “ON”. • Press primer knob (3) once. In cold weather press it twice or three times. • Pull the pull starter (4) slowly until some resistance is felt, then quickly and vigorously. Do not let the pull starter recoil quickly but lead it back slowly. • Set choke (2) back progressively to “OFF”. Start with electric starter (optional) (STH 5.56, STH 8.66, STH 10.66 C) To start the engine, the electric starter must be connected to the mains power supply. ! Risk of electric shock Make sure that the mains supply network is protected with a fault current circuit-breaker. If required, have an appropriate circuit-breaker fitted, but only by a trained electrician. For connecting the electric starter to the mains, use only extension cables (not supplied with the machine) which are approved for use in the open air and which are protected by an earth wire, e.g. up to a maximum length of 50 m: – H07RN-F 3x1.5 mm. up to –25 °C – H07BQ-F 3x1.5 mm. up to –40 °C. Caution If the electric starter is not connected properly, damage could occur to the machine or in its vicinity. Make sure that the mains supply network – is operating in conformity with the specifications on the starter identification plate (Figure 2, item 9) at 220–230 V and 50 Hz – is protected by an appropriate fuse system. • Put spark-plug connector (8) onto the spark plug. • Set throttle lever (7) to “ ”. • Insert ignition key (1) in the ignition lock, but do not turn it. • Connect extension cable first with the plug (5) and then with a mains socket. • Set choke (2) to “OFF”. • Press starter button (6) long enough (max. 5 sec.) for the engine to start. For a cold start, set choke (2) while the starter button is being pressed to “ ”. Wait at least 10 sec. before attempting to start the engine again. • As required, set the choke (2) progressively back to “OFF”. • Separate the extension cable first from the mains and then from the electric starter. Stop the engine Figure 2 • To avoid damage to the machine or starting problems arising from moisture, let the engine run for a few minutes before switching it off (to dry out). • (STH 5.56, STH 8.66, STH 10.66 C) Set throttle lever (7) to “ ”. • Ignition key (1) – (STH 953) turn to “OFF” and pull it out. – (STH 5.56, STH 8.66, STH 10.66 C) pull it out. • Set shut-off valve (10), if present, to “OFF”. Put in gear (Type 3 to Type 9) Figure 1 Caution Release coupling levers (1 and 2) before you select a gear or change gear. • Select a gear with the shift lever (6): – Forwards: “1” (slow) up to “5”/“6” (fast) – Reverse: “R” (slow) and “R ” (fast). Eliminate any blockages in the worm or the throw-out chute ! Risk of injury Before doing any work on this machine – Turn off the engine. – Wait until all moving ...
Este manual também é adequado para os modelos :Snow Blowers - STH 10.66 C (6.97 mb)
Snow Blowers - STH 8.66 (6.97 mb)