Store the spring clip in the lift rod hole. 4. Push the belt tensioning lever down. 6 Installation & Removal 5. Remove the belt from the PTO pulley (A, figure 5) and from the two idler pulleys (B & C). If a mower attachment is to be used on the tractor, remove the front idler pulley (D, figure 4) and install it in upper tab. 6. Remove the snowthrower from the tractor by using either one of the following methods “a” or “b”. (The belt may remain on snowthrower pulley unless removal is desired

• Slide the rubber dust cover (F) over the plastic fitting (B). 2 3 8 Figure 7 TP 1000-4518-01-LW-S Form No. 173xxxx-00 Two-Stage Snowthrower 1694986 10530L, 10.5 Snowthrower B A A C D B D Figure 3 A B C A B C D A B D E C D B A A B Remove Snowthrower From Crate • Cut the two zip ties from between wheels and the wood pallet. • Remove screws (A, Figure 11) from both skid shoes (B). • Roll snowthrower off crate. Add Oil and Fuel Note: Engine is NOT shipped with oil. Add 5W-30 premium engine oil. Se

Place the pivot pin through the blade assembly bracket and push bar. Position the push bar under the tractor front axel and attach it to the axel using two pins and spring clips. Attach the spring end of the lift rod to the push bar assembly and the other end to the tractor lift arm using two spring clips. OPERATION Alternate holes are provided to permit adjustment of the shoe assemblies for raising or lowering the blade when cleaning gravel drives or walks. When cleaning concrete it is desira

1/4 pages 8 & 7. 5 Simplicity Frame. Handle & Shroud Group T 76 Tighten nut (Raf. No. iß) 3 It lbs. max. Clutch lever must pivot frcoly. NOT£ U*e standard hardware torque spec. 173209 unless otherwise noted. A*fe to bottom out In palnut (Ref. No. 23). Mfg. No. 1690901 Ä 1690902 Frame. Handle & Shroud Group Simplicity Ref. No. Part No. Qty. Description 31 1664804 1 SWITCH, Ignition 32 916906 1 LOCKWASHER, Int Tooth. 5/8 33 933741 NUT. Speed, "U", #10 34 1664817 1 GUIDE. Choke K

No. 1691411 Mfg. No. 1691413 Mfg. No. 1691414 BakerTM OPERATOR’S MANUAL Model 7/22E 500 N. Spring Street, P.O. Box 997 Port Washinnton, WI 53074-0997 Table Of Contents SAFETY RULES General ........................................................... 2 Preparation.. .................................................. .2 Operation.. ..................................................... .2 Maintenance & Storage.. .............................. .3 Safety Decals ........................................

Traction 40 1707452 1 SPRING, Extension 41 1727088 1 ROD, 3/8" Diameter, 26" Long 42 1718793 1 SUPPORT, Gear 43 1960518 2 NUT, Push for 1/4 Diameter Thread 44 1960252 2 CARRIAGE BOLT, 1/4-20 x 5/8 G5 Footnotes The above parts group applies to the following Mfg. Nos.: 1694589 - 9560E 1694597 - 9560M © Copyright2005 Simplicity Manufacturing, Inc. All Rights Reserved. 9 TP 400-4155-01-LW-S Handles and Controls Group - 9560 Models NOTE: Unless noted otherwise, use the standard hardware torque specif

If it becomes necessary to move across the face of a slope, use caution and do not blow snow. Be very careful when changing direction on a slope. Proper winter footwear is recommended for the operator to help prevent slipping. Never attempt to clean snow from excessively steep slopes. The maximum slope for any operation is 35 percent ( 19.3° ) which is a rise of 3-1 /2 feet vertically in 10 feet horizontally. A WARNING To avoid serious injury, do not put your hands into the auger housing or dis

All Rights Reserved. 5 TP 400-4155-01-LW-S Handles and Controls Group - 1060, 1170, 1280 & 1390 Models NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Linkage adjustment for traction and auger drive with power boost: with drive levers engaged, the bottom end of lower rods (Ref. 40 & 66) should be flush with bottom of springs (Ref. 39 & 68). To engine ground Shift rod assembly (Ref. 71) must pivot freely on pivot blocks (Ref. 21). Torque to 19 - 29 ft-lbs. Moun

lbs. {2 places) Hook spring in slot. Belt Stops (Ref. No. 12 & 13) to be 1/16" to 1/16" over belt v.'»1M idler engaged. 10 Spring lo be hooked closed at assembly. Torque ilems 13, 36 & 42 105-130 in. lbs. /23 \ Torquo to 65-75 in. tbs. NOTE: U&e standard hardware torque spec. 17329Q unless otherwise noted. Torque lo 26 in. lbs. {■1 plRCM) AH Models Engine <5 Drive Group Simplicity Ref. Ho. Part. No. Qty. Description 1 1916964 1 LOCKWASHER, 1/4 2 1929486 1 CAPSCREW. Hex Hd.. 1/4-

All rights reserved Decals NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Not for The above parts group applies to the following Mfg. Nos.: 1695468 - 522E 1695514 - 522EX Briggs and Stratton Yard Power Products Group Copyright © 2008 by Briggs and Stratton Corporation 14 TP 400-5004-00-ST-S Milwaukee, WI, USA. All rights reserved Decals REF NO PART NO. QTY. DESCRIPTION 1 1736343YP 1 DECAL, Control Panel Electric Start (Domestic Only) 1 1740400MA 1 DECAL, Cont