This kit features a halogen bulb (replacement bulbs available) and includes all hardware and instructions. Order from Parts Division snowthrower model Honda code part number HS624, HS724 4155628 06350-767-100AH HS622TA 5335211 06600-743-800 HS828, HS928 4124400 06350-768-000AH Order from Parts Division Description Honda code part number Replacement bulb 4125886 34901-768-000AH AUGER RUBBER PARTS For easier servicing, here’s a complete auger rubber parts list. The auger rubber shoul

This will provide a controlled 6” plow depth and prevent the plow from going too deep in soft and/or wet spots. OPERATION PLOWADJUSTMENTS ,UPPER LINK Width ofCut Following proper assemblyand initial adjustments, the plow cut width will be 1 1" -12" when the right reat wheel is running against the furrow wall. Tochange the width, loosen the U-Bolts and move the beam along the mast an inch at a time to find the best width: Move to the right to decrease, and to the left to increase the width. NOTE

Normally, any problems concerning the product will be handled byyour dealer's' servicedpeartment. If you have a warranty problem that hasnot been handled to your satisfaction, we suggest you take the following action: Discuss your problem with a member of dealership management. Often complaints can be quickly resolved at that level. If the problem has already been reviewed with the ServiceManager, contact the owner of the dealership or the General Manager. If your problem still has not been reso

HO 1984 dick here to tau a this manual to your ocmputer. Thank you for purchasing a Honda snowblower. This manual covers the operation and maintenance of HS55/HS70 snowblowers. All information in this publication is based on the latest product information available at the time of approval for printing. Honda Motor Co., Ltd. reserves the right to make changes at any time without notice and without incurring any obligation. No part of this publication may be reproduced without written permis

3. After adjustment, retighten the ten- sion bolt lock nuts. TENSION BOLT 8. 8. I / i- i Before storing the snowblower for an extended period: 1. Be sure the storage area is free of excessive humidity and dust. 2. Drain the fuel - m Gasoline is extremely flammable and explosive under certain conditions. Do not smoke or allow flames or sparks in the area. FUEL ‘VALVE a. Drain the fuel. CARBURETOR DRAIN SCREW b. Loosen the carburetor drain screw, and drain the gasoline into a suitable container. R

Operating - 9 TROUBLESHOOTING Using Troubleshooting Chart If you are experiencing a problem that is not listed in this chart, see your Authorized Service Center for service. When you have checked all the possible causes listed and you are still experiencing the problem, see your Authorized Service Center. IF CHECK Engine Lugs Down Run engine at full throttle. Blade angle. Raise blade to float position. Adjust skid shoes. Blade Digs In Too Deep Raise blade to float position. Adjust skid shoes. Re

-All Rights Reserved I II I II I II I Ill Thank you for purchasing a Honda snowthrower. We want to help you get the best results from your new snowthrower and to operate it safely. This manual contains the information on how to do that; please read it carefully. Thank you for purchasing a Honda snowthrower. We want to help you get the best results from your new snowthrower and to operate it safely. This manual contains the information on how to do that; please read it carefully. This manual shou

Raise or lower the machine to the desired position. LOW : Hard snow or fine finish MIDDLE : Normal use HIGH : Dee’p snow or for transporting the snowblower. HEIGHT ADJUSTMENT BOLT SKID PLATE, SCRAPER SKID PLATE, SCRAPER (See page 14) HANDLEBAR HEIGHT ADJUSTMENT The handlebars can be set in the high, low or middle postion to suit the operator. To change handlebar height, remove the right and left adjusting bolts, align the bolt holes for the desired handlebar height, and reinstall the bolts. Tigh

Maintenance Follow the Maintenance Schedule on page 21. Remember that this schedule is based on the assumption that your machine will be used for its designed purpose. Sustained high-load operation will require more frequent service. TECHNICAL & CONSUMER INFORMATION Air Index An Air Index Information hang tag/label is applied to engines certified to an emission durability time period in accordance with the requirements of the California Air Resources Board. The bar graph is intended to provide y

. . . . . . . . . . . . . . . . . . . . .42 TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 EMISSION CONTROL SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 CONSUMER INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 INDEX . . . . . . . . . . . . . . . . . . . .