20. Use only attachments and accessories approved by the manufacturer. Failure to do so, can result in personal injury. 21. If situations occur which are not covered in this manual, use care and good judgment. Contact your dealer or telephone 1-800-800-7310 for assistance and the name of your nearest servicing dealer. Maintenance & Storage 1. Never tamper with safety devices. Check their proper operation regularly. 2. Check bolts and screws for proper tightness at frequent intervals to keep the

Snowthrower TRACTOR ASSEMBLY S/N 420280100101- 420280199999 85 0 J41 40 . . Ve TOUCH-UP PAINT SERVICE PARTS 200 Black Spray Paint 202 Loctite 242 201 Green Spray Paint 203 Tire Chains 7Г* Щ. 32 35 «к 29 Ч1 2 Model 42028 Ref.# Part# Description Qty. Ref.# Part# Description Qty. 1 1703539 Handle Grip............................................ 2 51 1756065021 Frame.................................................. . 1 2 1750796 Bumper..........................................

NOTE: When storing in a metal storage shed, rustproof the equipment, especially springs, cables and all moving parts.When storing any type of power equipment in a poorly ventilated or metal storage shed, care should be taken to rustproof the equipment, especially springs, cables and all moving parts. 10 SECTION 8: TROUBLESHOOTING GUIDE Problem Cause Remedy Engine fails to start 1. Fuel tank empty, or stale fuel 2. Blocked fuel line 3. Key not in ON position 4. Spark plug wire disconnected 5. Fau

MTD Products Ltd., P. O. Box 1386, KITCHENER, ONTARIO N2G 4J1 OPERATOR’S MANUAL IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATING EQUIPMENT. 769-04201 7/8/08 Single-Stage Snow Thrower - Model 2N1 & 2P5 This Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says. Table of Contents Safety Symbols................................................... 3

430355 10.19.09 SR Printed in the U.S.A. 20 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES (96192003302) AUGER HOUSING / IMPELLER ASSEMBLY 11 10 11 11 11 1 2 3 4 5 6 7 9 9 9 8 12 12 13 14 15 16 17 18 19 20 21 21 22 22 23 23 24 25 26 27 28 29 30 31 31 32 33 34 35

1 101 1187950 Shake-Proof Washer.................................. 1 46 1754272 Support Assembly............................ .......... 1 102 1714243 Flange Bearing........................................... ? 48 1727053 Pivot Block........................................ .......... 1 111 1760218 Speed Control Arm (also see 49 1186229 Hex Nut, 1/4-20................................ Ref. 111, pgs. 4-5)................................. 1 50 1764743 Auger Control Rod........................

(A) (C)............................. . 1 1757857 Housing Logo Decal (B)........................... 1 1725112001 Auger, L.H. (B) (D)............................ . 1 1916563 Housing Logo Decal (C)............................ 1 32 1186098 Carriage Bolt, 5/16-18 x 3/4.............. ? 1916564 Housing Logo Decal (D)........................... 1 33 1740553010 Scraper Blade (A).............................. . 1 72 1739792 Gear Case Assembly (A) (C)..................... 1 1758136010 Scraper

Refer to Figure 17. • Remove six self-tapping screws from the frame cover underneath the snow thrower. • Remove the klick pins which secure the wheels, and remove the wheels from the axle. • Using a wrench to hold the shaft, loosen, but do not completely remove, the hex nut and bell washer on the left end of gear shaft. See Figure 29. Hex Nut & Bell Washer Figure 29 • Lightly tap the hex nut to dislodge the ball bearing from the right side of the frame. Remove the hex nut and bell washer from th

An adjustable wrench and a 9/16" wrench is required. See figure 7. Tighten securely. 9 1G" WRENCH FIGURE 7 6 REAR SUPPORT ANGLE L.H. FIGURE 8 6. Preassemble the front support channel and the rear support angles as follows: A. Place the front support channel on a work bench or the floor. Place the rear support angles in position as shown in figure 8. B. Place the attaching plates between front support channel and rear support angles. See figure 8. C. Place hex bolts (G) through holes in

• P.O.BOX 2741 • CLEVELAND, OHIO 44111 FORM NO. 770-2863A Safety Rules for the Operation of Snow Throwers BEFORE STARTING: 1. Read the instruction manual and safety precautions furnished with your snow thrower before attempting to assemble or start it. 2. Familiarize yourself with the controls and use of the equipment. 3. Check the fuel level before each use to avoid refilling the tank while the engine is hot. Wipe off any gasoline spills and be sure the tank cap is snug. 4. Keep the area