60684 U.SoA. SAFETY RULES CAUTION: ALWAYS DISCONNECT SPARK PLUG WIRE AND A PLACE WIRE WHERE IT CANNOT CONTACT SPARK PLUG TO & PREVENT ACCIDENTAL STARTING WHEN SETTING-UP, TRANSPORTING, ADJUSTING OR MAKING REPAIRS. IMPORTANT SAFETY STANDARDS REQUIRE OPERATOR PRESENCE CONTROLS TO MINIMIZE THE RISK OF INJURY. YOUR SNOW THROWER IS EQUIPPED WITH SUCH CONTROLS. DO NOT ATTEMPT TO DEFEAT THE FUNCTION OF THE OPERATOR PRESENCE CONTROL UNDER ANY CIRCUMSTANCES, FUEL .SAFETY BEFORE USE ® Read the owner's man

A 9/16" or adjustable wrench is required. B. Slide the slotted end of the handles under the cupped washers. C. Secure the upper hole in the handles with 3/8" cupped washers and 2" long hex bolts. Cupped side of washers go against the handles. Do not tighten at this time. 5 I INSTALLING THE CHUTE CRANK ASSEMBLY 1. Attach the chute crank assembly to the handle and handle panel as follows. A. Thread one 5/16" hex nut about halfway onto the eyebolt on the chute crank assembly. B. Insert the

60684 U.S.A. Part No. 14200-04 Printed in U.S.A. 6/88 ONE YEAR LIMITED WARRANTY ON CRAFTSMAN SNOW THROWER For one year from the date of purchase, when this Craftsman Snow Thrower is maintained, lubricated and tuned-up according to the instructions in the owner’s manual. Sears will repair, Iree of charge, any defect in material and workmanship. H this Craftsman Snow Thrower is used for commercial purposes, this warranty applies for only 90 daysfrom the date of purchase. This warranty does n

756-0625 Roller, Cable 31. 790-00096 Front Guide Bracket, Auger Cable 32. 790-00180A Frame 33. 790-00206A Guide Bracket, Auger Cable Ref. No. 34. Part No. 790-00207A Description Guide Bracket, Drive Cable 35. 790-00316 Cover, Frame 36. 634-04167A LH Wheel Assembly, 13 x 4 x 6 634-04168A RH Wheel Assembly, 13 x 4 x 6 37. 731-04873 Spacer, 1.25 x .75 x 3.0 38. 738-04168 Axle, .75 x 22” 39. 741-0919 Ball Bearing 40. 710-0809 Hex Screw, 1/4-20, 1.25, Gr5 41. 710-0191 Hex Screw, 3/8-24, 1.25, Gr8 42.

Use SAE 5W30 engine oil only. FILL OIL This snow thrower was shipped with a container of 5W30 oil. This oil must be added to the engine before starting. For extreme cold operating conditions of 0° F or below, use a partial synthetic 0W30 motor oil for easier starting. NOTE: In areas where temperature is consistently at 2CP F or lower, you may use 0W30 motor oil for easier starting. • Remove the oil fill cap/dipstick. • Pour the oil and fill the crankcase to line (Full) on dipstick (19 ounce

DUAL STAGE SNOW THROWER Optional Electric Starter Available •Assembly •Operation •Maintenance •Repair Parts Sold by Sears, Roebuck and Co., Chicago, IL 60684 Pari No. 770-66750 (RB60B02) CRAFTSMAN WARRANTY LIMITED TWO YEAR WARRANTY ON CRAFTSMAN SNOW THROWER For two years from the date of purchase, when this Craftsman Snow Thrower ¡s maintained, lubricated and tuned up according to the instructions in the owner’s manual. Sears will repair, free of charge, any defect in material and workma

Operator’s Manual 28” SNOW THROWER Model No. 247.887900 • SAFETY • ASSEMBLY • OPERATION • MAINTENANCE • PARTS LIST • ESPANOL ® 7/6/2007 FORM NO. 769-02587A TABLE OF CONTENTS Warranty.Statement...................................Page.2 Repair.Protection.Agreement....................Page.3 Safe.Operation.Practices..........................Pages.4-5 Safety.Labels.............................................Page.7. Assembly...................................................Pages.8-11 Operation.......

247.888520 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. Sears, Roebuck And Co., Hoffman Estates, IL 60179, U.S.A. 770-10057B Printed in U.S.A. (10/98) TABLE OF CONTENTS TABLE OF CONTENTS Content Page Warranty Information .........................................2 Safe Operation Practices ...................................3 Assembly ...........................................................6 Operation ..............................

• Stop engine and wait several minutes before checking oil level. Remove oil fill cap and dipstick. • Wipe dipstick clean, insert it into oil fill hole and tighten securely. • Remove dipstick and check. If oil is not up to the FULL mark on dipstick, add oil. Changing Oil Change engine oil after first two hours of operation and every 25 hours thereafter. In order to change the oil, you will have to first drain the spent engine oil from the engine and then refill with fresh oil. • Drain oil while

This manual provides information regarding the setup, operation, and maintenance of this product. We have made every effort to ensure the accuracy of the information in this manual. The manufacturer reserves the right to change this product at any time without prior notice. Please keep this manual available to all users during the entire life of the snow thrower. Copyright 2005 Yardworks(R). Do not reprint without written authorization. TABLE OF CONTENTS GENERAL SAFETY PROCEDURES ...............