Follow all lock out/tag out procedures established by the user. Verify all power is off to the unit before performing any work. Failure to comply could result in serious injury, death or damage to the equipment. Wiring Diagram of GIB Control If housing and plugs are damaged during disassembly please refer to the drawing below to for proper location of inputs and outputs and wires. Each plug is keyed for proper placement. Revision Date: May 17, 2012 Revision: C © 2003-2012, IMI Cornelius Inc

With the side panel off inspect that the wires are free and not trapped where they could become pinched and short out to the cabinet frame. NOTE: It is also recommended that before reattaching the panels to the machine reinstall the control and verify machine functions properly. If any part of the dispenser does not function properly such as pumps, disconnect power and reinstall GIB control. Be sure connector is seated properly in connectors. © 2003-2012, IMI Cornelius Inc. - 3 - Publication

PREVIEW QUESTIONS Check your current knowledge by taking a few minutes to answer the following questions: 1. The 5 and 3-gallon bowl assemblies are interchangeable on certain models? _____ True _____ False 2. Parts that contain Microban need not be cleaned on a regular basis? _____ True _____ False 3. All visual cold units use only one type of circulator for all products that are dispensed from the machine? _____ True _____ False 4. Is it possible to add a whipper assembly to a unit after a unit

Dispense all of the hot water into a large container. Repeat for the remaining dispense valves. 5. Remove the mixing chambers, nozzles, and static mixers. Rinse in hot water to remove excess pulp and concentrate. 6. Place the mixing chambers, nozzles, and static mixers in a separate container of sanitizing solution and agitate vigorously. Allow the parts to soak for two minutes. Rinse thoroughly with fresh tap water. 7. Reinstall the static mixer, nozzles, and mixing chambers. © 2004, IMI Cornel

Follow all lock out/tag out procedures established by the user. Verify all power is off to the unit before performing any work. Failure to comply could result in serious injury, death or damage to the equipment. Wiring Diagram of GIB Control If housing and plugs are damaged during disassembly please refer to the drawing below to for proper location of inputs and outputs and wires. Each plug is keyed for proper placement. Revision Date: May 17, 2012 Revision: C © 2003-2012, IMI Cornelius Inc

3.3 Condenser Dissipates heat from the compressor and prepares the high pressure refrigerant for the capillary tube and ultimately the evaporator. 3.4 Condenser Cleaning It is very important to do this on an annual basis and as required. The condenser can be cleaned with a brush or compressed air. There are commercial condenser cleaners on the market that are acceptable. 3.5 Filter Replacement The Jet Spray unit comes with a foam type filter mounted on the inside of the side panel assembly. JT30

© 2004, IMI Cornelius Inc. - 1 -Publication Number: TP00968 Quest Juice Training Manual DIMENSIONS & CAPACITIES Quest Dispense Rate ........................................1.0 – 2.2 oz./sec. Electrical rating .......................................115 VAC, 60 Hz, 15 amp dedicated circuit ................................................................220 VAC, 50Hz Dimensions .............................................29.3” H, 24.3” D Condenser clearance..............................4” back, 12

2 Remove the new seal from its packaging. 3 Clean the spacer. 4 Slide the spacer (with slots toward the motor housing) over the motor shaft. 5 Lubricate the inside of the seal using Dow Corning 111 Lubricant and Sealant. (Note, Do not lubricate the static side (outer portion) of the seal. This could cause the seal to rotate in the bore and leak.) 6 Carefully slide the seal over the motor shaft and press it firmly until is fully seated against the spacer and the seal cannot be pushed any further.

Each plug is keyed for proper placement. Revision Date: May 17, 2012 Revision: C © 2003-2012, IMI Cornelius Inc. - 1 - Publication Number: 729011138INS Replacing GIB Controller on Quest Juice Dispensers Figure 1. Removal of GIB Control 1. Disconnect power from unit. 2. Remove dispensing nozzles. 3. To remove splash panel located at the bottom of the unit remove two screws left and right side and slide splash panel forward. 4. To remove top panel open door and locate two screws at the re

Follow all lock out/tag out procedures established by the user. Verify all power is off to the unit before performing any work. Failure to comply could result in serious injury, death or damage to the equipment. Wiring Diagram of GIB Control If housing and plugs are damaged during disassembly please refer to the drawing below to for proper location of inputs and outputs and wires. Each plug is keyed for proper placement. Revision Date: May 17, 2012 Revision: C © 2003-2012, IMI Cornelius Inc