Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Note on comparative tests: For testing the test programmes, wash the specified load using the maximum spin speed. Programme Additional function Load Annual energy consumption Annual water consumption ..Cottons/Coloureds..40/60 °C ....ecoPerfect** 7/3,5 kg 197 kWh 10560 l ** Programme setting for testing and energy labelling in accordance with EU directive 2010/30/EU with cold water (15 .C). *** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient temperature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected additional functions. 9 Care Before washing for the first time Do not load any laundry into the machine. Turn on the tap. Add the following to compartment II: – approx. 1 litre water – detergent (dosage according to the manufacturer's instructions for light soiling and the appropriate degree of water hardness) Set the programme selector to .. Easy-Care 60 °C and select .. (Start/Pause). At the end of the programme, turn the programme selector to Off. Machine housing, control panel – Wipe with a soft, damp cloth. – Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners). – Remove detergent and cleaning agent residue immediately. – Do not clean with a jet of water. Cleaning the detergent drawer... ...if it contains detergent or fabric softener residues. 1. Pull out, press insert down, remove draw completely. 2. To remove the insert: press the insert upwards from below with your finger. 3. Clean the detergent dispenser tray and insert with water and a brush and dry it. 4. Attach the insert and engage (connect the cylinder to the guide pin). 5. Push in the detergent drawer. Leave the detergent drawer open so that any residual water can evaporate. Drum Leave the washing machine door open so that the drum can dry out. Rust stains - use chlorine-free cleaning agent, not steel wool. Descaling Ensure there is no laundry in the machine Descale the appliance according to the descaler manufacturer's instructions. This should not be necessary if the correct dosage of detergent is used. Information on the indicator lights model-dependent A signal sounds and indicator lights for the spin speed flash: ¤ ¤ ¤ ¤ ¤ Close the washing machine door properly; laundry may be caught. ¤ ¤ ¤ ¤ ¤ Detergent solution pump blocked; Clean the detergent solution pump .. page 10. Drainage hose/waste pipe blocked; Clean the drainage hose at the siphon .. page 10. ¤ ¤ ¤ ¤ ¤ Open the tap completely, supply hose kinked or trapped; Clean the filter .. page 10, Water pressure too low. ¤ ¤ ¤ ¤ ¤ Motor fault. Call the aftersales service. ¤ ¤ ¤ ¤ ¤ Water in the base tub, appliance leaking. Call the after-sales service. – Risk of electric shock. Disconnect the mains plug. – Risk of explosion. No solvents. 10 Maintenance Detergent solution pump Turn the programme selector to Off and disconnect the mains plug. 1. Open and remove the service flap. 2. For models with a drainage hose: Remove the drainage hose from the retainer and pull it from the housing. Remove the container. Remove the sealing cap, allow the detergent solution to flow out. Replace the sealing cap and place the drainage hose in the retainer. 2* For models without a drainage hose: Carefully unscrew the pump cover until the detergent solution begins to flow out. When the service flap is half full, close the pump cover and empty the service flap. Repeat the above steps until all the detergent solution has completely drained out. 3. Carefully unscrew the pump cover (residual water). 4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent solution pump must rotate). 5. Replace the pump cover and screw it in place tightly. 6. Place the service flap back on and close. To prevent unused detergent from flowing straight into the drain during the next wash: Pour 1 litre of water into compartment II and start the .. Empty programme. Drainage hose at the siphon Turn the programme selector to Off and disconnect the mains plug. 1. Loosen the hose clamp, carefully remove the drainage hose (residual water). 2. Clean the drainage hose and siphon connecting piece. 3. Reattach the drainage hose and secure the connection with the hose clamp. Filter in the water supply Risk of electric shock. Do not immerse the HydroSafe safety device in water (contains an electric valve). Reduce the water pressure in the supply hose: 1. Turn off the tap. 2. Select any programme (except for ....Rinse/....Spin // .. Empty). 3. Select ....(Start/Pause). Let the programme run for approximately 40 seconds. 4. Turn the programme selector to Off. Disconnect the mains plug. Clean the filter: 1. Depending on model: Disconnect the hose from the tap. Clean the filter using a small brush. and/or for Standard and Aqua-Secure models: Remove the hose on the rear of the appliance, Remove the filter with pliers and clean. 2. Connect the hose and check for leaks....