Assessments - 4, GPA: 3.3
(
)
)
|
Facilidade de uso
reach of children and other untrained persons. A tool is dangerous in the hands of untrained users. Maintain the tool with care. f. A properly maintained tool is more efficient and reduces the risk of binding and is easier to control. Check for misalignment or bindg. ing of moving parts, breakage of parts, and any other condition that affects the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. There is a risk of bursting if the tool is damaged. Use only accessories that are h. identified by the manufacturer for the specific tool model. Use of an accessory not intended for use with the specific tool model, increases the risk of injury to persons. Use only those fasteners listed i. in the Accessories section of this manual. Fasteners not identified for use with this tool by the tool manufacturer are able to result in a risk of injury to persons or tool damage when used in this tool. Service Tool service must be performed a. only by qualified repair personnel. When servicing a tool, use only b. identical replacement parts. Use only authorized parts. Use only the lubricants supplied c. with the tool or specified by the manufacturer. Air source a. Never connect to an air source that is capable of exceeding 90 PSI. Over pressurizing the tool may cause bursting, abnormal operation, breakage of the tool or serious injury to persons. Use only clean, dry, regulated compressed air at the rated pressure or within the rated pressure range as marked on the tool. Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air-pressure range. Never use oxygen, carbon dioxide, b. combustible gases or any bottled gas as an air source for the tool. Such gases are capable of explosion and serious injury to persons. Save these instructions. Symbols and Specific Safety Instructions Symbol Definitions Symbol Property or statement PSI Pounds per square inch of pressure CFM Cubic Feet per Minute flow SCFM Cubic Feet per Minute flow at standard conditions NPT National pipe thread, tapered NPS National pipe thread, straight WARNING marking concerning Risk of Eye Injury. Wear ANSI-approved eye protection. Warning marking concerning Risk of Puncture Injury. Wear heavy-duty work gloves. Read the manual before set-up and/ or use. WARNING marking concerning Risk of Hearing Loss. Wear hearing protection. WARNING marking concerning Risk of Respiratory Injury. Wear NIOSH- approved dust mask/respirator. WARNING marking concerning Risk of Explosion. Specific Safety Instructions Operators and others in work area 1. MUST wear ANSI-approved safety goggles with side shields during use. The employer is responsible to enforce use of eye protection by the operator and others in the work area. Keep fingers away from Trigger 2. when not driving fasteners to avoid accidental firing. Always assume the tool contains 3. fasteners. Do not point the tool toward yourself 4. or anyone whether it contains fasteners or not. Do not actuate the tool unless the 5. tool is placed firmly against the workpiece. Respect tool as a working implement.6. No horseplay. This tool is not a toy 7. and can be deadly if misused. Do not load the tool with fasteners 8. when any one of the operating controls is activated. Do not remove, tamper with, or other9. wise cause the tool operating controls to become inoperable. Do not operate the tool if any portion 10. of the tool operating controls is inoperable, disconnected, altered, or not working properly. Disconnect the tool from the power 11. source when: Unattended.a. Performing any maintenance or b. repair. Clearing a jam.c. Moving the tool to a new location.d. The written approval of the tool man12. ufacturer must be obtained prior to making any modifications to the tool. Refer to the tool maintenance instruc13. tions for detailed information on the proper maintenance of the tool. Fire fasteners into an appropriate 14. work surface only. Do not attempt to fire fasteners into surfaces too hard to penetrate. Do not drive fasteners on top of other fasteners, or at too steep of an angle. Fasteners can ricochet causing personal injury. Do not fire fasteners too close to the 15. edge of a workpiece. They may split the workpiece and fly free, causing personal injury. Transport Tool safely. Always dis16. connect air supply when moving the tool. Carry the tool by the handle and avoid contact with the trigger. Hold tool away from head and body. 17. During operation the Tool may kick back causing injury. Do not fire fasteners into a workpiece 18. that has people, utility lines, or other objects behind or inside it. Keep balance while using this tool. 19. Keep area below clear if working in a high location, and secure air hose to prevent falls from bystanders accidentally pulling on it. Obey the manual for the air compres20. sor used to power this tool. Install in-line shutoff valve to allow im21. mediate co...