Clean and inspect tool daily. Carefully check for proper operation of trigger and safety mechanism. Do Not use the tool unless both the trigger and the safety mechanism are functional, or if the tool is leaking air or needs any other repair. Fig. 24 S RUBBER NOSE CUSHION A rubber nose cushion (A) Fig. 25 is provided to reduce marring of the work surface. The rubber cushion can be removed when it is not required. Disconnect tool from air supply before removing or installing rubber cushion. Fig. 2

Fig. 9. 16. Only use parts and accessories approved by DeVilbiss Air Power Company. 17. Connect tool to air supply before loading fasteners, to prevent a fastener from being fired during connection. The tool driving mechanism may cycle when tool is connected to the air supply. Fig. 10. 18. Always assume the tool contains fasteners. No horseplay. Respect the tool as a working implement. Fig. 11. 19. Operator and bystanders should wear hard hats to safeguard against possible injuries. Fig. 12. 20.

A05982 -07-22-04 TABLE OF CONTENTS SAFETY GUIDELINES AND INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . .3 GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6 FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 PREPARING THE TOOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

7 PREPARING THE TOOL NOTE: This tool is shipped completely assembled. No assembly time or tools are required. 1. After reading and understanding this entire manual, connect tool to air supply (Fig. 18). 2. Depress latch and slide magazine core open (Fig. 19). 3. Turn the tool upside down. Insert a strip of fasteners into the magazine channel (A) Fig. 20. With the tool upside down, orient fasteners with points up in the magazine channel (B) Fig. 20. NOTE: Staples are loaded from the bottom. 4. Pu

11. Connect tool to air supply hose with a coupling that automatically removes all pressure from the tool when the coupling is disconnected. Fig. 7. 12. Disconnect tool from air supply hose before doing tool maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, or handing the tool to another person. Fig. 7. 13. Never use a tool that is leaking air, has missing or damaged parts, or requires repair. Make sure all screws and caps are securely tightened. Fig. 8

ESPANOL: PAGINA 13 FRANCAISE : PAGE 25 Copyright © 2004 DeVilbiss Air Power Company Part No. A05983 -07-22-04 TABLE OF CONTENTS SAFETY GUIDELINES AND INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . .3 GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6 FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 PREPARING THE TOOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Max. P.S.I. Operating Pressure Range Air Inlet Weight Height Length Width Type of Fastener Fastener Lengths Fastener Capacity NF2502X4 120 70-120 1/4" NPT 4.66 10.25 11.75 3 Finish Nail 16 Gauge See page 17 110 pcs. SNC1002X4 120 70-120 1/4" NPT 2.3 7.5 11.3 2.25 Narrow Crown Staple 18 Gauge See page 18 150 pcs. NB2002X4 120 70-120 1/4" NPT 2.6 8.1 9 2 Brad Nail 18 Gauge See Page 19 110 NB1252X4 120 70-120 1/4" NPT 2.55 7.75 9.75 2.25 Brad Nail 18 Gauge See page 20 110 pcs. NBSNC2X4 120 57-110 1

DO NOT USE detergent oil or additives. Operate the tool briefly after adding oil. (See Figure 1) DO NOT OVER LUBRICATE AIR TOOL. 3. Wipe off excessive oil at the exhaust. NOTE Many air tool users find it convenient to use an Oiler to help provide oil circulation through tool. An Oiler also increases the efficiency and useful life of the tool. An oiler is recommended for tools that receive heavy or constant use. Check oil level in the oiler daily. (See Figure 2) Many air tool users find it conven

Do not use the tool if the contact trip safety mechanism is not working correctly. 1. Disconnect the air supply from the tool. 2. Remove all fasteners from the magazine. Make sure not to pull the trigger or depress the contact trip safety mechanism when connecting the tool to an air compressor. Serious personal injury or property damage can occur if the tool cycles. 3. Make sure the trigger and contact trip safety mechanism move up and down without any sticking or binding. 4. Reconnect air suppl

See specification label on tool for the maximum P.S.I. Unsuitable Cleaning Solvents Flammable vapors in the tool will ignite by a spark and could cause the tool to explode! Never use gasoline or other flammable liquids to clean the tool. PAGE 4 Risk of head injury. HAZARD TO LOOK FOR WHAT COULD HAPPEN HOW TO PREVENT IT Injury to eyes, head and hearing Metal fragments, fasteners, or other material could be projected against head or into eyes resulting in serious injury or property damage. Continu